Infiniti P0154 A/F Sensor 21 Heater System Malfunction

Description

OBD-II Trouble Code Description for P0154 Infiniti

O2 Sensor Circuit No Activity Detected

What does this mean?

OBD2 Code P0154 Infiniti definition:
The oxygen sensors are critical to the engine running properly. It basically informs the PCM (Powertrain Control Module) of oxygen content of the exhaust. The PCM then uses this information to regulate fuel into the engine and maintain proper air:fuel ratio. It is a four wire sensor, with the PCM providing a reference/signal voltage of about half a volt (0.5v) to the sensor. It usually provides a ground also. The other two wires are dedicated to the oxygen sensor heater element. This heater allows the sensor to warm up faster, which allows the engine to enter closed loop faster, reducing startup emissions. The heater element is supplied a 12v feed from the power distribution center (usually) and a ground. The oxygen content of the exhaust affects the O2 sensor resistance. This resistance produces a counter voltage on the reference/signal wire that the PCM will use to analyze oxygen in the exhaust. Lean exhaust produces low voltage, while rich exhaust produces high voltage. The oxygen sensor is capable of varying between 0.9v (rich) and 0.1v (lean). Once the engine reaches closed loop, the O2 sensor should begin switching rapidly between rich and lean voltages 2-3 times per second. If for some reason the O2 sensor doesn’t switch properly or “sticks”, P0154 Infiniti may set. This code indicates the O2 sensor isn’t operating.

Symptoms

Possible sumptoms of OBD code P0154 Infiniti
Symptoms of a P0154 Infiniti code may include: MIL (Malfunction Indicator Lamp) illumination Other codes indicating rich or lean condition may be present Poor idle, won’t idle Misfire at idle or at highway speed Engine may blow black smoke at tailpipe Fuel economy may decrease May start and stall

Causes

Possible causes of OBD code P0154 Infiniti
Potential causes of a P0154 Infiniti code include: Faulty bank 2,1 Oxygen sensor Holes in exhaust near oxygen sensor Short to voltage or ground on signal circuit Open or high resistance in signal circuit Wiring harness chafing/rubbing on exhaust components Water/oil intrusion at O2 sensor connector Broken lock or loose terminals on O2 sensor connector Oil/coolant fouled oxygen sensor

Possible Solutions

First start the engine and bring it up to operating temperature and ensure the engine reaches closed loop. Then, using the live data function on a scan tool, observe the Bank 2,1 oxygen sensor voltage reading. Is it switching properly? If so, the problem may be an intermittently bad sensor or more likely a wiring problem. Visually check the O2 sensor wiring and repair as needed. Does the voltage for the Bank 2,1 oxygen sensor appear to be “stuck” and not moving? If so, increase idle speed for 30 seconds or so. If the sensor begins switching after a period of elevated idle, visually check the exhaust for holes or rust near the O2 sensor that could be affecting the voltage reading If the exhaust checks out, suspect the sensor to be sluggish and replace it. If the Bank 2,1 oxygen sensor appears to be not switching, turn the engine off, and unplug the Bank 2,1 oxygen sensor. With KOEO (Key on engine off) jumper the O2 sensor signal wire to the ground wire. Now the voltage reading should be low (about 0.1v). If it is, then check for a bad connection at the O2 sensor connector. Repair as necessary. If no bad connection is found, replace the O2 sensor and re-check. If when you jumper the signal wire to the ground wire the voltage reading isn’t low (about 0.1v), remove the jumper wire. Now check for voltage at the O2 sensor signal wire. It should have, with KOEO and O2 sensor unplugged, roughly 0.5 volts. If it does, check also for a good ground to the sensor as well. Repair as necessary Check for loose connections, water intrusion at PCM connector, etc. If you have no 0.5 volt reference voltage, unplug the PCM connector and ohm the signal circuit and ground circuits. There should be no resistance nor any voltage. Repair excessive resistance. If you still have no 0.5 volt reference voltage, recheck at the PCM connector. It may be necessary to clip the signal wire to eliminate the possibility of a short or open somewhere. If you now have reference voltage present coming out of the PCM, fix open/short in signal circuit. If you have no reference voltage coming out of the PCM, the PCM will have to be diagnosed for a fault. It may be the problem.


The OBD2 Code Information Be Applicable For Infiniti:

,2013 Infiniti M35h GT,2013 Infiniti JX,2013 Infiniti FX,2011 Infiniti QX,2011 Infiniti M35h,2011 Infiniti M,2011 Infiniti JX Concept,2011 Infiniti IPL G Coupe,2011 Infiniti EX30d,2009 Infiniti G37,2009 Infiniti FX50,2009 Infiniti FX37,2009 Infiniti FX35,2009 Infiniti Essence Concept,2009 Infiniti EX37,2008 Infiniti QX56,2008 Infiniti M45x,2008 Infiniti M45s,2008 Infiniti G37 Coupe,2008 Infiniti EX35,2007 Infiniti G35 Sedan,2007 Infiniti EX Concept,2006 Infiniti QX56,2006 Infiniti Q45,2006 Infiniti M45,2006 Infiniti M35x,2006 Infiniti M35,2006 Infiniti FX45,2005 Infiniti Q45,2005 Infiniti G35,2005 Infiniti FX45,2004 Infiniti QX56,2004 Infiniti M45 Concept,2004 Infiniti I35,2003 Infiniti QX4,2003 Infiniti Q45,2003 Infiniti M45,2003 Infiniti I35,2003 Infiniti G35,2003 Infiniti FX45,2003 Infiniti FX35

 

Note:

1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Infiniti makes.

2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.

3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.

4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.

5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.