Infiniti P0403 Exhaust Gas Recirculation Control Circuit

Description

OBD-II Trouble Code Description for P0403 Infiniti

Exhaust Gas Recirculation Control Circuit

What does this mean?

OBD2 Code P0403 Infiniti definition:
The Exhaust Gas Recirculation (EGR) system is controlled by a vacuum solenoid. The solenoid is supplied ignition voltage. The Powertrain Control Module (PCM) controls the vacuum solenoid by grounding the control circuit(ground) or driver. The primary function of the driver is to supply ground for the object that is being controlled. Each driver has a fault circuit that the PCM monitors. When the PCM turns a component on, the control circuit voltage is low, or close to zero. When the component is turned off, the voltage on the control circuit is high, or near battery voltage. The PCM watches for these conditions, and if it doesn’t see the proper voltage at the proper time, this code is set.

Symptoms

Possible sumptoms of OBD code P0403 Infiniti
Usually a fault in the control circuit, will leave no noticeable symptoms other than the Malfunction Indicator Lamp (MIL) illumination. However, if the EGR control solenoid is stuck open due to debris, etc. the code may be accompanied by misfire under acceleration, rough idle, or engine dying altogether.

Causes

Possible causes of OBD code P0403 Infiniti
The causes for a P0403 Infiniti EGR code could be any of the following: Bad EGR solenoid Excessive resistance in control circuit (PCM controlled ground) due to an open, chafing or damage to the harness Poor connection at the EGR solenoid harness (worn or loose pins) Water intrusion at the EGR solenoid harness Blockage in EGR control solenoid holding solenoid open or closed causing excessive resistance Loss of supply voltage to EGR solenoid Bad PCM

Possible Solutions

With the ignition on and engine off, use a scan tool to activate the EGR solenoid. Listen or feel for a clicking, indicating that the solenoid is operating. If the solenoid does operate, you’ll have to check current draw on the ground circuit. It should be less than one amp. If it is then the problem is intermittent. If it isn’t then there is excessive resistance in the circuit and perform the following 1. When it’s activated see if you can blow lightly through it. IF you can’t there may be a blockage causing excessive resistance. Replace EGR solenoid as needed. If there is no blockage, disconnect the EGR solenoid and the PCM connector containing the EGR solenoid control circuit. Using a digital Volt-Ohm meter (DVOM) check resistence between the control circuit and battery ground. It should be infinite. If it isn’t, then there is a short to ground on the control circuit. Repair the short to ground and retest as needed. 2. If the solenoid doesn’t click as it should, disconnect the EGR solenoid connector and connect a test light between the two wires. Using the scan tool, command the EGR solenoid on. The light should light up. If it does, replace the EGR solenoid. If it does not perform the following: a. Check for 12 Volts on the ignition supply voltage to the solenoid. If it isn’t present, inspect the supply circuit for an open, or a short due to chafing or breakage and re-test. b. If it still doesn’t operate: then manually ground the EGR solenoid control circuit. The light should light. If it does, repair open in EGR solenoid control circuit and re-test. If it doesn’t, replace EGR solenoid.

Related Codes

P0400 Infiniti P0401 Infiniti P0402 Infiniti


The OBD2 Code Information Be Applicable For Infiniti:

,2013 Infiniti M35h GT,2013 Infiniti JX,2013 Infiniti FX,2011 Infiniti QX,2011 Infiniti M35h,2011 Infiniti M,2011 Infiniti JX Concept,2011 Infiniti IPL G Coupe,2011 Infiniti EX30d,2009 Infiniti G37,2009 Infiniti FX50,2009 Infiniti FX37,2009 Infiniti FX35,2009 Infiniti Essence Concept,2009 Infiniti EX37,2008 Infiniti QX56,2008 Infiniti M45x,2008 Infiniti M45s,2008 Infiniti G37 Coupe,2008 Infiniti EX35,2007 Infiniti G35 Sedan,2007 Infiniti EX Concept,2006 Infiniti QX56,2006 Infiniti Q45,2006 Infiniti M45,2006 Infiniti M35x,2006 Infiniti M35,2006 Infiniti FX45,2005 Infiniti Q45,2005 Infiniti G35,2005 Infiniti FX45,2004 Infiniti QX56,2004 Infiniti M45 Concept,2004 Infiniti I35,2003 Infiniti QX4,2003 Infiniti Q45,2003 Infiniti M45,2003 Infiniti I35,2003 Infiniti G35,2003 Infiniti FX45,2003 Infiniti FX35

 

Note:

1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Infiniti makes.

2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.

3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.

4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.

5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.