Description
OBD-II Trouble Code Description for P0404 Jeep
Exhaust Gas Recirculation Control Circuit Range/Performance
What does this mean?
OBD2 Code P0404 Jeep definition:
The EGR (Exhaust Gas Recirculation) system’s purpose is to redirect exhaust gas back into the cylinders. Since exhaust gas is inert, it displaces oxygen and fuel, thereby lowering cylinder temps, which, in turn, lowers oxides of nitrogen emissions. For that reason it needs to be carefully metered into the cylinders (via the EGR valve) so as not to adversely affect the engine’s performance. (Too much EGR and the engine won’t idle). If you have a P0404 Jeep, then the EGR valve is likely an electrically controlled EGR valve instead of a vacuum controlled EGR valve. Also, the valve will usually have a feedback system built into it that informs the PCM (Powertrain Control Module) what position the valve is in; open, closed, or somewhere in between. The PCM needs to know this to determine whether or not the valve is operating as needed. If the PCM determines that the valve should be operating, but the feedback circuit shows that the valve is not open, this code will set. Or if the PCM determines the valve should be closed but the feedback signal indicates that the valve is open, this code will set.
Symptoms
Possible sumptoms of OBD code P0404 Jeep
There may be no symptoms of a P0404 Jeep DTC other than the MIL (malfunction indicator lamp) or check engine light. However, Exhaust Gas Recirculation systems are inherently problematic due to carbon buildup in the intake manifold, etc. This normal buildup can lodge in an EGR valve, holding it open when it should be closed. If this is the case, the engine may idle rough, or not at all. If the valve has failed and is NOT opening, then symptoms would be higher combustion temps and as a result, higher Nox emissions. But the latter symptoms aren’t going to be noticeable to a driver.
Causes
Possible causes of OBD code P0404 Jeep
Usually this code points to either carbon buildup or a bad EGR valve. However that doesn’t rule out the following: Open or short in the 5 Volt reference circuit Open or short in the ground circuit Open or short in the PCM controlled voltage circuit Bad PCM (less likely)
Possible Solutions
Using a scan tool command the EGR valve to open while watching the actual EGR position (it will probably be labeled “desired EGR” or something similar). The actual EGR position should be very close to the “desired” EGR position. If it is, then the problem is likely intermittent. It may have been a lodged piece of carbon that has since dislodged, or it could be a bad EGR valve winding that intermittently opens or shorts as the valve temperature changes. If the EGR “desired” position is not close to the “actual” position, then unplug the EGR sensor. Check for a good 5 Volt reference voltage to the connector. If it doesn’t show a reference voltage, repair an open or short in the 5 Volt reference circuit. If there is a 5 volt reference voltage, activate the EGR with the scanner, monitor the EGR ground circuit with a DVOM (Digital Volt/Ohm meter). It should indicate a good ground. If it doesn’t then repair the ground circuit. If there is a good ground, then check the control circuit. It should indicate voltage that varies according to the percentage that the EGR is open. As it’s open more, the voltage should increase accordingly. If it does, then replace the EGR valve. If the voltage doesn’t increase incrementally, then repair open or short in EGR control circuit.
The OBD2 Code Information Be Applicable For Jeep:
,2013 Jeep Wrangler Unlimited Moab,2013 Jeep Wrangler Rubicon 10th Anniversary,2013 Jeep Grand Cherokee Trailhawk,2012 Jeep Wrangler Unlimited Altitude,2012 Jeep Wrangler Freedom Edition,2012 Jeep Wrangler Dragon Concept,2012 Jeep Wrangler Call of Duty MW3,2012 Jeep Wrangler Arctic,2012 Jeep Wrangler,2012 Jeep Liberty Arctic,2012 Jeep Grand Cherokee SRT8,2012 Jeep Grand Cherokee Concept,2011 Jeep Wrangler Mojave,2011 Jeep Wrangler Call of Duty Black Ops,2011 Jeep Wrangler,2011 Jeep Patriot,2011 Jeep Grand Cherokee UK Version,2011 Jeep Grand Cherokee,2011 Jeep Compass,2009 Jeep Wrangler Unlimited EV,2009 Jeep Patriot EV,2008 Jeep Wrangler Unlimited UK Version,2008 Jeep Wrangler UK Version,2008 Jeep Renegade Concept,2008 Jeep Patriot Back Country Concept,2008 Jeep Liberty,2008 Jeep Grand Cherokee S-Limited UK Version,2008 Jeep Grand Cherokee Overland UK Version,2008 Jeep Grand Cherokee,2008 Jeep EV Concept,2008 Jeep Cherokee,2007 Jeep Wrangler Unlimited,2007 Jeep Wrangler Rubicon,2007 Jeep Trailhawk Concept,2007 Jeep Patriot UK Version,2007 Jeep Patriot,2007 Jeep Grand Cherokee UK Version,2007 Jeep Grand Cherokee SRT-8 UK Version,2007 Jeep Compass UK Version,2007 Jeep Compass,2007 Jeep Commander UK Version,2006 Jeep Grand Cherokee SRT8,2006 Jeep Commander 4×4 Limited 5.7 HEMI,2005 Jeep Wrangler UK Version,2005 Jeep Patriot Concept,2005 Jeep Liberty Renegade 3.7,2005 Jeep Liberty CRD Limited,2005 Jeep Hurricane Concept,2005 Jeep Grand Cherokee 5.7 Limited,2005 Jeep Gladiator Concept,2005 Jeep Compass Concept,2005 Jeep Cherokee UK Version,2004 Jeep Wrangler Unlimited,2004 Jeep Rescue Concept,2003 Jeep Treo Concept,2003 Jeep Grand Cherokee UK Version,2003 Jeep Cherokee UK Version,2003 Jeep Cherokee Renegade,2002 Jeep Willys2 Concept
Note:
1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Jeep makes.
2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.
3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.
4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.
5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.