Land Rover P0111 Intake Air Temperature Circuit Range/Performance Problem

Description

OBD-II Trouble Code Description for P0111 Land Rover

IAT Circuit Malfunction

What does this mean?

OBD2 Code P0111 Land Rover definition:
The IAT (Intake Air Temperature) sensor is a thermistor that varies resistance based upon the temperature of the engine intake air. Usually a two wire sensor. One wire is supplied 5 Volt from the PCM (Powertrain Control Module) and the other is a ground. The PCM monitors the change in the 5 Volt supplied to determine air temperature. When the intake air is cold, the resistance is high, resulting in a high signal voltage. When the intake air is warm, the reistance is low, resulting in a low signal voltage. This code means that the PCM saw a larger-than-normal change in a shorter-than-expected time on the IAT signal circuit.

Symptoms

Possible sumptoms of OBD code P0111 Land Rover
Since this code is likely pointing to an intermittent problem on the IAT circuit, there may not be any symptoms at present. However, the MIL will likely be on. The car MAY exhibit some drivability problems, but it is more likely that there will be no noticeable symptoms to the driver.

Causes

Possible causes of OBD code P0111 Land Rover
a bad IAT sensor an open in the signal or ground circuit a short to ground on the signal circuit poor connection at sensor or PCM

Possible Solutions

If there are other IAT codes present, diagnose them first. If not, then, using a scan tool verify the IAT voltage with KOEO (Key on engine off). If, on a cold engine it reads the same as the CTS (Coolant temperature sensor), then the problem is intermittent. But if the IAT reading isn’t the same as the CTS refer to diagnostic procedure for P0110 Land Rover. If your scan tool has a freeze frame failure records feature, use it to see what the IAT reading was at the time of the failure. If the reading was at negative 30 or so degrees F (indicating it was at the extreme coldest reading), then there was an intermittent high resistance reading on the IAT signal circuit. Check for an open ground on the ground circuit and signal circuit. If they are OK, try raising and lowering the temperature of the IAT sensor artificially. Do this by removing the IAT and putting it in a freezer and then applying heat with a heat gun (be careful not to apply too much heat to the IAT with the heat gun or it’ll melt the sensor). Watch the resistance change using an ohmmeter attached to each terminal. It should vary smoothly with no sudden jumps. If the reading jumps suddenly, then repace the IAT sensor. However if the freeze frame reading was at the highest extreme (above 250 deg. F) then there was an intermittent low resistance on the signal circuit. Check for a short to ground on the signal circuit. If it appears OK, then do the above artificial heat test and replace the IAT as necessary. If the problem can’t be duplicated, use a voltmeter to watch the signal voltage as you “wiggle” test the wiring harness. Watch for a sudden change in voltage indicating a short or open. Replace IAT as necessary. This is a pretty simple code and it only really looks for extremely short changes that are relatively high in voltage. It’s usually the sensor that is bad unless the vehicle is extremely old, in which case there may be harness problems.

Related Codes

P0095 Land Rover P0096 Land Rover P0097 Land Rover P0098 Land Rover P0099 Land Rover P0109 Land Rover P0110 Land Rover P0112 Land Rover P0113 Land Rover P0114 Land Rover


The OBD2 Code Information Be Applicable For Land Rover:

2013 Land Rover,2012 Land Rover,2011 Land Rover,2010 Land Rover,2009 Land Rover ,2008 Land Rover,2007 Land Rover,2006 Land Rover,2005 Land Rover,2004 Land Rover,2003 Land Rover,2002 Land Rover

 

Note:

1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Land Rover makes.

2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.

3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.

4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.

5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.