Lexus P0150 Air Fuel Ratio Circuit Bank 2 Sensor 1

Description

OBD-II Trouble Code Description for P0150 Lexus

O2 Sensor Circuit

What does this mean?

OBD2 Code P0150 Lexus definition:
The O2 sensor produces a voltage based on oxygen content in the exhaust. The voltage varies between .1 and .9 Volts, .1 indicating lean and .9 indicating rich. The ECM constantly monitors this voltage while in closed loop to determine how much fuel to inject. If the ECM determines that the O2 sensor voltage was too low (less than .4 Volts) for too long (for more than 20 seconds (time varies with model)), this code is set. The code P0150 Lexus definition:Bank 2.

Symptoms

Possible sumptoms of OBD code P0150 Lexus
Depending if the problem is intermittent or not, there may be no symptoms other than MIL (malfunction indicator lamp) illumination. If the problem is constant, then symptoms may include one or more of the following: MIL illumination Engine runs rough, missing or stumbling Blows black smoke from tail pipe Engine dies Poor fuel economy

Causes

Possible causes of OBD code P0150 Lexus
Usually the cause of P0150 Lexus is a bad oxygen sensor, however this isn’t always the case. If your o2 sensors haven’t been replaced and they are old, it’s a good bet that the sensor is the problem. But, It could be caused by any of the following: Water or corrosion in the connector Loose terminals in the connector Wiring burnt on exhaust components Open or short in the wiring due to rubbing on engine components Holes in exhaust allowing unmetered oxygen into exhaust system Unmetered vacuum leak at the engine Bad o2 sensor Bad PCM

Possible Solutions

Using a scan tool, determine if the Bank 2, sensor 1 is switching properly. It should switch rapidly between rich and lean, evenly. 1. If it does, the problem is likely intermittent and you should examine the wiring for any visible damage. Then perform a wiggle test by manipulating the connector and wiring while watching the o2 sensor voltage. If it drops out, fix the appropriate part of the wiring harness where problem resides. 2. If it doesn’t switch properly, try to determine if the sensor is accurately reading the exhaust or not. Do this by removing the fuel pressure regulator vacuum supply briefly. The o2 sensor reading should go rich, reacting to the extra fuel added. Reinstall regulator supply. Then induce a lean condition by removing a vacuum supply line from the intake manifold. The o2 sensor reading should go lean, reacting to the enleaned exhaust. If the sensor operates properly, then the sensor may be okay and the problem may be holes in the exhaust or an unmetered vacuum leak in the engine (NOTE: Unmetered vacuum leaks at the engine are almost always accompanied by lean codes. Refer to the appropriate articles for diagnosing an unmetered vacuum leak). If the exhaust does have holes in it, it’s possible that the o2 sensor may be misreading the exhaust because of the extra oxygen entering the pipe via those holes 3. If none of this is the case and the o2 sensor just isn’t switching or acts sluggish, unplug the sensor and make sure there is 5 Volt reference voltage to the sensor. Then check for 12V supply to the o2 sensor’s heater circuit. Also check for continuity to ground on the ground circuit. If any of these are missing, or aren’t their proper voltage, repair open or short in the appropriate wire. The o2 sensor will not operate properly without proper voltage. If the proper voltages are present, replace the o2 sensor.


The OBD2 Code Information Be Applicable For Lexus:

2013 Lexus RX 450h F Sport,2013 Lexus RX 450h,2013 Lexus RX 350 F Sport,2013 Lexus RX 350,2013 Lexus LX 570,2013 Lexus LS EU-Version,2013 Lexus LS 600h L,2013 Lexus LS 460 F Sport,2013 Lexus LS 460,2013 Lexus LF-NX Concept,2013 Lexus GS 450h F Sport,2013 Lexus GS 450h,2013 Lexus GS 350 F Sport,2013 Lexus GS 350,2013 Lexus GS 250,2013 Lexus ES 300h,2013 Lexus ES350,2012 Lexus LF-LC Concept,2012 Lexus LF-CC Concept,2011 Lexus LFA,2011 Lexus LF-Gh Concept,2011 Lexus IS 350 F Sport,2011 Lexus IS 350,2011 Lexus CT 200h,2010 Lexus SC 430,2010 Lexus RX 450h,2010 Lexus RX 350,2010 Lexus LS 600h,2010 Lexus LS 460 Sport,2010 Lexus LS 460 L,2010 Lexus IS250C,2010 Lexus HS 250h,2010 Lexus GX 460,2010 Lexus GS 460,2010 Lexus GS 450h,2010 Lexus GS 350,2010 Lexus ES 350,2009 Lexus SC430,2009 Lexus LS,2009 Lexus LS460,2009 Lexus LF-Ch,2009 Lexus IS 350,2009 Lexus GX 470,2009 Lexus GS 460,2009 Lexus GS 450h,2009 Lexus GS 350,2008 Lexus LX 570,2008 Lexus LS 600h L,2007 Lexus LS,2007 Lexus LF,2006 Lexus SC,2006 Lexus IS350,2006 Lexus GS,2005 Lexus RX400h,2005 Lexus LFA Concept,2005 Lexus ES330,2004 Lexus RX330,2004 Lexus LS430

 

Note:

1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Lexus makes.

2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.

3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.

4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.

5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.