Lincoln P0209 Injector Circuit Malfunction Cylinder 9

Description

OBD-II Trouble Code Description for P0209 Lincoln

Injector Circuit/Open – Cylinder 9

What does this mean?

OBD2 Code P0209 Lincoln definition:
P0208 Lincoln means that the PCM detected a fault in the injector or the wiring to the injector. It monitors the injector and when the injector is activated, the PCM expects to see the voltage pulled “low” or close to zero. When the injector is switched off, the PCM expects to see a voltage that is close to battery voltage or “high”. If it doesn’t see the expected voltage the PCM will set this code. The PCM also monitors resitance in the circuit. If the resistance is excessively low or high it will set this code.

Symptoms

Possible sumptoms of OBD code P0209 Lincoln
The symptoms for this code will likely be a misfire and a rough running engine. Poor acceleration. The MIL will also be illuminated.

Causes

Possible causes of OBD code P0209 Lincoln
The causes of a P0208 Lincoln engine light code could be any of the following: Bad injector. This is usually the cause of this code but doesn’t rule out the possibility of one of the other causes Open in the wiring to the injector Short in the wiring to the injector Bad PCM

Possible Solutions

First, using a DVOM check the resistance of the injector. If it isn’t within specs, then replace the injector. Check for voltage at the fuel injector connector. It should have 10 volts or more. Visually check the connector for damage or broken wires. Visually check the injector for damage. If you have access to an injector tester, activate the injector and see if it operates. If the injector operates, then you likely have either an open in the wiring, or a blocked injector. If you do not have access to a tester, swap the injector with another one and see if the code changes. If the code changes, then change the injector. At the PCM, remove the driver wire from the PCM connector and Ground the wire. (Make sure you have the correct wire. If you’re not sure, do not attempt) The injector should activate Replace the injector First, using a DVOM check the resistance of the injector. If it isn’t within specs, then replace the injector. Check for voltage at the fuel injector connector. It should have 10 volts or more. Visually check the connector for damage or broken wires. Visually check the injector for damage. If you have access to an injector tester, activate the injector and see if it operates. If the injector operates, then you likely have either an open in the wiring, or a blocked injector. If you do not have access to a tester, swap the injector with another one and see if the code changes. If the code changes, then change the injector. At the PCM, remove the driver wire from the PCM connector and Ground the wire. (Make sure you have the correct wire. If you’re not sure, do not attempt) The injector should activate Replace the injector


The OBD2 Code Information Be Applicable For Lincoln:

2013 Lincoln MKZ,2013 Lincoln MKT,2013 Lincoln MKS,2013 Lincoln MKC,2012 Lincoln MKZ,2011 Lincoln MKX,2010 Lincoln MKZ,2010 Lincoln MKT,2009 Lincoln MKS,2009 Lincoln C Concept,2008 Lincoln MKT Concept,2007 Lincoln Navigator,2007 Lincoln MKZ,2007 Lincoln MKX,2007 Lincoln MKR Concept,2006 Lincoln Zephyr,2006 Lincoln Mark LT,2006 Lincoln MKS Concept,2004 Lincoln Mark X Concept,2004 Lincoln Aviator Concept,2003 Lincoln Town Car,2003 Lincoln Aviator,2001 Lincoln MK9

 

Note:

1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Lincoln makes.

2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.

3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.

4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.

5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.