Description
OBD-II Trouble Code Description for P0341 Mazda
Camshaft Position Sensor “A” Circuit Range/Performance
What does this mean?
OBD2 Code P0341 Mazda definition:
This P0341 Mazda code basically means that the powertrain control module (PCM) detected a problem with the camshaft signal. The camshaft position sensor (CPS) sends a specific signal to the PCM for Top Dead Center on the compression stroke as well as signals indicating the position of the cam sensor. This is accomplished through a reluctor wheel attached to the camshaft that passes by the cam sensor. Any time that the signal to the PCM is inconsistent with what the signal should be, this code is set. NOTE: this code can also be set by extended cranking periods.
Symptoms
Possible sumptoms of OBD code P0341 Mazda
The car will likely run with this code set, as it is often intermittent and also because the PCM can often operate the vehicle in “limp-in/limp-home” mode even with a cam sensor signal problem. There may be no noticeable symptoms other than: Poor fuel economy (if engine runs) Possible no start condition
Causes
Possible causes of OBD code P0341 Mazda
A code P0341 Mazda may mean that one or more of the following has happened: Cam sensor wiring routed too close to spark plug wiring (causing interference) Poor wiring connection at cam sensor Poor wiring connection at PCM Bad cam sensor Damaged reluctor wheel
Possible Solutions
Often relacing the sensor fixes this code, but not necessarily. Therefore it’s important to check the following: Check that the wiring isn’t routed too close to any secondary ignition components (coil, spark plug wires, etc.) Visually inspect the wiring at the sensor for any burn marks, discoloration indicative of melting or chafing Visually inspect the cam sensor for damage Visually inspect the reluctor wheel through the cam sensor port (if possible) for any missing teeth or any damage If reluctor isn’t visible from outside the engine, visual test can only be done by removing cam shaft or intake manifold (depending on engine design) If all checks out okay, then replace the sensor. Related Camshaft Trouble Codes: P0340 Mazda
The OBD2 Code Information Be Applicable For Mazda:
2013 Mazda MX-5,2013 Mazda MX-5,2013 Mazda CX-9,2013 Mazda CX-5,2013 Mazda 6,2013 Mazda 5,2013 Mazda 3,2012 Mazda MX-5,2012 Mazda BT-50,2012 Mazda 3,2011 Mazda 6,2011 Mazda 5,2011 Mazda 2,2010 Mazda 3,2009 Mazda 6,2009 Mazda 2 ,2008 Mazda 6,2008 Mazda 6,2008 Mazda 5,2008 Mazda 2,2007 Mazda CX-9,2007 Mazda CX-7,2006 Mazda MX5,2006 Mazda 6,2006 Mazda 3,2005 Mazda Atenza,2004 Mazda 6,2004 Mazda 5,2003 Mazda 2,2002 Mazda 6
Note:
1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Mazda makes.
2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.
3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.
4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.
5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.