Description
OBD-II Trouble Code Description for P0208 Mazda
Injector Circuit/Open – Cylinder 8
What does this mean?
OBD2 Code P0208 Mazda definition:
P0207 Mazda means that the PCM detected a fault in the injector or the wiring to the injector. It monitors the injector and when the injector is activated, the PCM expects to see the voltage pulled “low” or close to zero. When the injector is switched off, the PCM expects to see a voltage that is close to battery voltage or “high”. If it doesn’t see the expected voltage the PCM will set this code. The PCM also monitors resitance in the circuit. If the resistance is excessively low or high it will set this code.
Symptoms
Possible sumptoms of OBD code P0208 Mazda
The symptoms for this code will likely be a misfire and a rough running engine. Poor acceleration. The MIL will also be illuminated.
Causes
Possible causes of OBD code P0208 Mazda
The causes of a P0207 Mazda engine light code could be any of the following: Bad injector. This is usually the cause of this code but doesn’t rule out the possibility of one of the other causes Open in the wiring to the injector Short in the wiring to the injector Bad PCM
Possible Solutions
First, using a DVOM check the resistance of the injector. If it isn’t within specs, then replace the injector. Check for voltage at the fuel injector connector. It should have 10 volts or more. Visually check the connector for damage or broken wires. Visually check the injector for damage. If you have access to an injector tester, activate the injector and see if it operates. If the injector operates, then you likely have either an open in the wiring, or a blocked injector. If you do not have access to a tester, swap the injector with another one and see if the code changes. If the code changes, then change the injector. At the PCM, remove the driver wire from the PCM connector and Ground the wire. (Make sure you have the correct wire. If you’re not sure, do not attempt) The injector should activate Replace the injector First, using a DVOM check the resistance of the injector. If it isn’t within specs, then replace the injector. Check for voltage at the fuel injector connector. It should have 10 volts or more. Visually check the connector for damage or broken wires. Visually check the injector for damage. If you have access to an injector tester, activate the injector and see if it operates. If the injector operates, then you likely have either an open in the wiring, or a blocked injector. If you do not have access to a tester, swap the injector with another one and see if the code changes. If the code changes, then change the injector. At the PCM, remove the driver wire from the PCM connector and Ground the wire. (Make sure you have the correct wire. If you’re not sure, do not attempt) The injector should activate Replace the injector
The OBD2 Code Information Be Applicable For Mazda:
2013 Mazda MX-5,2013 Mazda CX-9,2013 Mazda CX-5,2013 Mazda 6,2013 Mazda 5,2013 Mazda 3,2012 Mazda CX-5,2012 Mazda BT-50,2012 Mazda 3,2011 Mazda 6,2011 Mazda 5,2011 Mazda 2,2010 Mazda CX-7,2010 Mazda 3,2009 Mazda RX-8,2009 Mazda MX-5,2009 Mazda CX9,2009 Mazda 6,2009 Mazda 2,2008 Mazda MX-5,2008 Mazda 6,2008 Mazda 5,2008 Mazda 2,2007 Mazda CX-9,2007 Mazda CX-7,2006 Mazda MX5,2006 Mazda 6,2006 Mazda 3,2005 Mazda Atenza,2005 Mazda 6,2004 Mazda MPV,2004 Mazda 6,2004 Mazda 5,2004 Mazda 3,2003 Mazda RX-8
Note:
1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Mazda makes.
2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.
3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.
4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.
5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.