Nissan P0362 Ignition Coil 12 Primary/Secondary Circuit Malfunction

Description

OBD-II Trouble Code Description for P0362 Nissan

Ignition Coil “L” Primary/Secondary Circuit

What does this mean?

OBD2 Code P0362 Nissan definition:
The COP (coil on plug) ignition system is what is used on most modern engines. There is an individual coil for each cylinder that is controlled by the PCM (powertrain control module). It eliminates the need for spark plug wires by putting the coil right above the sparkplug. Two wires are dedicated to each coil. One is a battery feed usually from the power distribution center. The other wire is the coil driver circuit from the PCM. The PCM grounds/ungrounds this circuit to activate or deactivate the coil. The coil driver circuit is monitored by the PCM for faults If an open or a short is detected in the driver circuit for coil number 12, a P0322 Nissan may set. Also, depending on the vehicle, the PCM may also shut down the fuel injector to the cylinder also.

Symptoms

Possible sumptoms of OBD code P0362 Nissan
MIL (Malfunction indicator lamp) illumination Engine misfire may be present or intermittent

Causes

Possible causes of OBD code P0362 Nissan
Short to voltage or ground on COP driver circuit Open on COP driver circuit Loose connection at coil or broken connector locks Bad Coil (COP) Faulty Powertrain Control Module

Possible Solutions

Is the engine misfiring presently? If not, the problem is likely intermittent. Try wiggle testing the wiring at the #3 coil and along the wiring harness to the PCM. If manipulating the wiring causes the misfire to surface, repair the wiring problem. Check for poor connection at the coil connector. Verify the harness isn’t misrouted or chafing on anything. Repair as necessary If the engine is misfiring presently, stop the engine and disconnect the #3 coil wiring connector. Then start the engine and check for a driver signal to the #3 coil. Using a scope will give you a visual pattern to observe, but since most people don’t have access to one there’s an easier way. Use a Voltmeter in AC Hertz scale and see if there’s a Hz reading of between 5 and 20 or so that indicates the driver is working. If there is a Hertz signal, then replace the #3 ignition coil. It’s likely bad. If you don’t detect any frequency signal from the PCM on the ignition coil driver circuit indicating the PCM is grounding/ungrounding the circuit (or there is no visible pattern on the scope if you have one) then leave the coil disconnected and check for DC voltage on the driver circuit at the ignition coil connector. If there is any significant voltage on that wire then there is a short to voltage somewhere. Find the short and repair it. If there is no voltage on the driver circuit, then turn the ignition off. Disconnect the PCM connector and check the continuity of the driver between the PCM and the coil. If there is no continuity repair the open or short to ground in the circuit. If continuity is present, then check for resistance between ground and the ignition coil connector. There should be infinite resistance. If there isn’t, repair the short to ground in the coil driver circuit NOTE: If the ignition coil driver signal wire is not open or shorted to voltage or ground and there is no trigger signal to the coil then suspect a faulty PCM coil driver. Also keep in mind that if the PCM driver is at fault, there may be a wiring problem that caused the PCM failure. It’s a good idea to do the above check after PCM replacement to verify there won’t be a repeat failure. If you find that the engine isn’t misfiring, the coil is being triggered properly but P0362 Nissan is continually being reset, there is the possibility that the PCM coil monitoring system may be faulty.


The OBD2 Code Information Be Applicable For Nissan:

2013 Nissan Pathfinder,2013 Nissan Murano,2013 Nissan Juke Nismo,2013 Nissan GT-R,2013 Nissan Altima Sedan,2013 Nissan Almera,2013 Nissan 370Z,2012 Nissan Tiida,2012 Nissan Sunny,2012 Nissan Qashqai,2012 Nissan Murano,2012 Nissan Micra ELLE,2012 Nissan Micra DIG-S,2012 Nissan Maxima,2012 Nissan Juke Shiro,2012 Nissan GT-R,2012 Nissan Extrem Concept,2011 Nissan X-Trail,2011 Nissan Rogue,2011 Nissan Quest,2011 Nissan Pivo 3 Concept,2011 Nissan Patrol,2011 Nissan Murano,2011 Nissan Micra,2011 Nissan LEAF,2011 Nissan Juke,2011 Nissan GT-R,2011 Nissan 370Z,2010 Nissan Qashqai,2010 Nissan Pathfinder,2010 Nissan Navara,2010 Nissan NV200,2010 Nissan GT-R SpecV,2010 Nissan Cube,2010 Nissan Altima Sedan,2010 Nissan Altima Coupe,2010 Nissan 370Z Roadster,2009 Nissan Xterra,2009 Nissan Pixo,2009 Nissan Note,2009 Nissan Murano,2009 Nissan Maxima,2009 Nissan Frontier,2009 Nissan 370Z,2008 Nissan X-Trail,2008 Nissan Rogue,2008 Nissan Pathfinder,2008 Nissan GT-R,2007 Nissan Sentra SE-R,2007 Nissan Mixim,2007 Nissan Altima,2006 Nissan Urge Concept,2006 Nissan Note,2006 Nissan 350Z,2005 Nissan Zaroot Concept,2005 Nissan Xterra,2005 Nissan Terrano,2005 Nissan Sport Concept,2005 Nissan Primera,2005 Nissan Pivo Concept,2005 Nissan Pickup,2005 Nissan Patrol,2005 Nissan Pathfinder,2005 Nissan Micra,2005 Nissan Altima,2004 Nissan Titan,2004 Nissan Tiida

 

Note:

1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Nissan makes.

2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.

3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.

4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.

5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.