Peugeot P0121 Throttle Position Sensor 1 Performance

Description

OBD-II Trouble Code Description for P0121 Peugeot

Throttle/Pedal Position Sensor/Switch “A” Circuit Range/Performance

What does this mean?

OBD2 Code P0121 Peugeot definition:
The Throttle position sensor is a potentiometer that measures the amount of throttle opening. As the throttle is opened, the reading (measured in volts) goes up. The powertrain control module (PCM) supplies a 5 Volt reference signal to the throttle position sensor (TPS) and usually a ground also. A general measurement is: at idle = .5 Volts; full throttle = 4.5 Volts. If the PCM detects that the throttle angle is greater or less than it should be for a specific RPM, it will set this code.

Symptoms

Possible sumptoms of OBD code P0121 Peugeot
Symptoms of a P0121 Peugeot trouble code could include: Malfunction Indicator Lamp (MIL) illumination (Check Engine Light or Service Engine Soon light) Intermittent stumble on acceleration or deceleration Blows black smoke on acceleration No start

Causes

Possible causes of OBD code P0121 Peugeot
A code P0121 Peugeot may mean that one or more of the following has happened: TPS has intermittent open or short internally Harness is rubbing and causing an open or short in the wiring Bad connection at the TPS Bad PCM (less likely) Water or corrosion in connector or sensor

Possible Solutions

1. If you have access to a scan tool, see what the idle and WOT (wide open throttle) readings are for the TPS. Check if they’re close to the specifications mentioned above. If not, then replace the TPS and re-check. 2. Check for an intermittent open or short in the TPS signal. To do that, you can’t use a scan tool. You’ll need an oscilliscope. The reason is because scan tools take samplings of many different readings over just one or two data lines and can miss an intermittent drop out. Hook up your oscilliscope and watch the signal. It should sweep up and down smoothly with no drop outs or spikes. 3. If no problems were noticed, perform a wiggle test. Do this by wiggling the connector and harness while watching the pattern. Does it drop out? If so, replace TPS and re-check. 4. If you have no TPS signal, check for 5 Volt reference at the connector. If it’s present, check the ground circuit for open or shorts. 5. Make sure the signal circuit isn’t 12V. It should never have battery voltage. If it does, trace circuit for short to voltage and repair. 6. Look for any water in the connector and replace TPS as necessary.

Related Codes

P0120 Peugeot P0122 Peugeot P0123 Peugeot P0124 Peugeot

 


The OBD2 Code Information Be Applicable For Peugeot:

2013 Peugeot 508,2013 Peugeot 4008,2013 Peugeot 308,2013 Peugeot 208,2013 Peugeot 107,2012 Peugeot 308,2012 Peugeot 208,2011 Peugeot 508,2011 Peugeot 408,2011 Peugeot 308,2010 Peugeot 207,2010 Peugeot 207,2009 Peugeot 407,2009 Peugeot 308,2009 Peugeot 206,2009 Peugeot 107,2008 Peugeot 308,2008 Peugeot 207,2007 Peugeot 308,2007 Peugeot 207,2006 Peugeot 407,2006 Peugeot 207,2006 Peugeot 206,2005 Peugeot 407,2005 Peugeot 307,2005 Peugeot 206,2005 Peugeot 107,2005 Peugeot 1007,2004 Peugeot 607,2004 Peugeot 407,2004 Peugeot 206,2003 Peugeot 307,2003 Peugeot 206

 

Note:

1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Peugeot makes.

2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.

3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.

4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.

5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.