Description
OBD-II Trouble Code Description for P0209 Acura
Injector Circuit/Open – Cylinder 9
What does this mean?
OBD2 Code P0209 Acura definition:
P0208 Acura means that the PCM detected a fault in the injector or the wiring to the injector. It monitors the injector and when the injector is activated, the PCM expects to see the voltage pulled “low” or close to zero. When the injector is switched off, the PCM expects to see a voltage that is close to battery voltage or “high”. If it doesn’t see the expected voltage the PCM will set this code. The PCM also monitors resitance in the circuit. If the resistance is excessively low or high it will set this code.
Symptoms
Possible sumptoms of OBD code P0209 Acura
The symptoms for this code will likely be a misfire and a rough running engine. Poor acceleration. The MIL will also be illuminated.
Causes
Possible causes of OBD code P0209 Acura
The causes of a P0208 Acura engine light code could be any of the following: Bad injector. This is usually the cause of this code but doesn’t rule out the possibility of one of the other causes Open in the wiring to the injector Short in the wiring to the injector Bad PCM
Possible Solutions
First, using a DVOM check the resistance of the injector. If it isn’t within specs, then replace the injector. Check for voltage at the fuel injector connector. It should have 10 volts or more. Visually check the connector for damage or broken wires. Visually check the injector for damage. If you have access to an injector tester, activate the injector and see if it operates. If the injector operates, then you likely have either an open in the wiring, or a blocked injector. If you do not have access to a tester, swap the injector with another one and see if the code changes. If the code changes, then change the injector. At the PCM, remove the driver wire from the PCM connector and Ground the wire. (Make sure you have the correct wire. If you’re not sure, do not attempt) The injector should activate Replace the injector First, using a DVOM check the resistance of the injector. If it isn’t within specs, then replace the injector. Check for voltage at the fuel injector connector. It should have 10 volts or more. Visually check the connector for damage or broken wires. Visually check the injector for damage. If you have access to an injector tester, activate the injector and see if it operates. If the injector operates, then you likely have either an open in the wiring, or a blocked injector. If you do not have access to a tester, swap the injector with another one and see if the code changes. If the code changes, then change the injector. At the PCM, remove the driver wire from the PCM connector and Ground the wire. (Make sure you have the correct wire. If you’re not sure, do not attempt) The injector should activate Replace the injector
The OBD2 Code Information Be Applicable For Acura:
2014 Acura RLX,2014 Acura MDX,2013 Acura SUV-X Concept,2013 Acura RDX,2013 Acura NSX Concept,2013 Acura MDX Concept,2013 Acura ILX Endurance Racer,2013 Acura ILX,2012 Acura TL,2012 Acura RLX Concept,2012 Acura NSX Concept,2012 Acura ILX Street Build Concept,2012 Acura ILX Concept,2011 Acura TSX Sport Wagon,2011 Acura TSX Sedan,2010 Acura ZDX,2010 Acura TSX V6,2010 Acura RDX,2010 Acura MDX,2009 Acura ZDX Concept,2009 Acura TSX,2009 Acura TL,2009 Acura RL,2007 Acura TSX,2007 Acura TL Type-S,2007 Acura TL,2007 Acura RDX,2007 Acura MDX,2007 Acura Advanced Sports Car Concept,2006 Acura RDX Prototype,2006 Acura MD-X Concept,2006 Acura Advanced Sedan Concept,2005 Acura TSX A-Spec Concept,2005 Acura TSX,2005 Acura TL,2005 Acura RSX Type-S,2005 Acura RSX A-Spec Concept,2005 Acura RSX,2005 Acura RL with ASPEC Performance Package,2005 Acura RL ASPEC Concept,2005 Acura RL,2005 Acura RDX Concept,2005 Acura NSX,2005 Acura MDX,2004 Acura TL with ASPEC Performance Package,2004 Acura TL 25 Hours of Thunderhill,2004 Acura RL Prototype,2004 Acura 3.2 TL,2003 Acura TL ASPEC Concept,2003 Acura 3.2 CL Type-S,2002 Acura NSX sketches,2001 Acura NSX-T,2001 Acura Integra
Note:
1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Acura makes.
2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.
3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.
4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.
5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.