Skoda P0207 Injector 7 Control Circuit

Description

OBD-II Trouble Code Description for P0207 Skoda

Injector Circuit/Open – Cylinder 7

What does this mean?

OBD2 Code P0207 Skoda definition:
P0207 Skoda means that the PCM detected a fault in the injector or the wiring to the injector. It monitors the injector and when the injector is activated, the PCM expects to see the voltage pulled “low” or close to zero. When the injector is switched off, the PCM expects to see a voltage that is close to battery voltage or “high”. If it doesn’t see the expected voltage the PCM will set this code. The PCM also monitors resitance in the circuit. If the resistance is excessively low or high it will set this code.

Symptoms

Possible sumptoms of OBD code P0207 Skoda
The symptoms for this code will likely be a misfire and a rough running engine. Poor acceleration. The MIL will also be illuminated.

Causes

Possible causes of OBD code P0207 Skoda
The causes of a P0207 Skoda engine light code could be any of the following: Bad injector. This is usually the cause of this code but doesn’t rule out the possibility of one of the other causes Open in the wiring to the injector Short in the wiring to the injector Bad PCM

Possible Solutions

First, using a DVOM check the resistance of the injector. If it isn’t within specs, then replace the injector. Check for voltage at the fuel injector connector. It should have 10 volts or more. Visually check the connector for damage or broken wires. Visually check the injector for damage. If you have access to an injector tester, activate the injector and see if it operates. If the injector operates, then you likely have either an open in the wiring, or a blocked injector. If you do not have access to a tester, swap the injector with another one and see if the code changes. If the code changes, then change the injector. At the PCM, remove the driver wire from the PCM connector and Ground the wire. (Make sure you have the correct wire. If you’re not sure, do not attempt) The injector should activate Replace the injector First, using a DVOM check the resistance of the injector. If it isn’t within specs, then replace the injector. Check for voltage at the fuel injector connector. It should have 10 volts or more. Visually check the connector for damage or broken wires. Visually check the injector for damage. If you have access to an injector tester, activate the injector and see if it operates. If the injector operates, then you likely have either an open in the wiring, or a blocked injector. If you do not have access to a tester, swap the injector with another one and see if the code changes. If the code changes, then change the injector. At the PCM, remove the driver wire from the PCM connector and Ground the wire. (Make sure you have the correct wire. If you’re not sure, do not attempt) The injector should activate Replace the injector

Related Codes

P0200 Skoda P0201 Skoda P0202 Skoda P0203 Skoda P0204 Skoda P0205 Skoda P0206 Skoda P0208 Skoda P0209 Skoda P0210 Skoda


The OBD2 Code Information Be Applicable For Skoda:

2013 Skoda Rapid,2013 Skoda Octavia,2013 Skoda Citigo,2011 Skoda Roomster,2011 Skoda Fabia,2010 Skoda Superb,2009 Skoda Superb,2009 Skoda Octavia,2008 Skoda Fabia,2007 Skoda Fabia,2006 Skoda Roomster,2006 Skoda Octavia,2005 Skoda Octavia,2005 Skoda Fabia,2003 Skoda Superb,2003 Skoda Octavia,2003 Skoda Fabia

 

Note:

1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Skoda makes.

2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.

3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.

4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.

5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.