Volkswagen P0144 O2 Sensor Circuit High Voltage Bank 1 Sensor 3

Description

OBD-II Trouble Code Description for P0144 Volkswagen

O2 Sensor Circuit High Voltage

What does this mean?

OBD2 Code P0144 Volkswagen definition:
The catalytic converter is used to lower harmful emissions. To ensure proper operation, there is an O2 sensor located behind the catalyst that monitors the oxygen content of the exhaust after the cat. The PCM (Powertrain Control Module) then compares the post-cat reading to the pre-cat readings to determine if the catalyst is working properly. A P0144 Volkswagen definition:a fault at the post-cat o2 sensor, indicating that the signal voltage is too high. The o2 sensor is a four wire sensor. Two wires are dedicated to the heating element and two wires are dedicated to the sensor. The heating element should have battery voltage on one wire with key on engine off and ground should be present on the other. The PCM supplies a reference voltage to the o2 sensor which the sensor varies according to oxygen content in the exhaust. It is capable of varying between approximately 0.1 and 0.9 volts. This variance in the voltage is monitored by the PCM. The PCM also supplies a ground to the sensor. P0144 Volkswagen means that the voltage was too high on the signal circuit.

Symptoms

Possible sumptoms of OBD code P0144 Volkswagen
Symptoms of a P0144 Volkswagen DTC may include: MIL (Malfunction Indicator Lamp) on Engine loses power and misses intermittently May exhibit loss of fuel efficiency

Causes

Possible causes of OBD code P0144 Volkswagen
Potential causes of an P0144 Volkswagen code include: Bad o2 sensor (Bank 1 Sensor 3) Wiring in contact with exhaust components Engine running rich (If other codes are present) Holes in exhaust near Bank 1 Sensor 3 Short to voltage on signal circuit Bad PCM

Possible Solutions

Start the engine and observe the Bank 1 Sensor 3 (a.k.a. 1/3) o2 sensor voltage. You may need to raise the idle up until the o2 sensor starts switching. If it is stuck high, or close to 1 volt and the voltage doesn’t vary, then check for a good ground on both the heater element and the sensor. Also check that the heater element is being supplied good battery voltage. No heater operation can cause a sluggish sensor. If the grounds are good and the battery voltage is present, then jumper the sensor’s signal wire to the sensor’s ground wire. Now the scan tool should read low or near zero volts. If it does, the wiring is good. Replace the bank 1/3 o2 sensor. If jumpering the signal wire to the ground doesn’t lower the voltage, then check the o2 sensor wiring harness. Make sure there is no contact with hot exhaust components. Ensure good wiring harness connections. If the wiring checks out, then reperform the previous wiring harness checks at the PCM connector. If now the 1/3 o2 sensor reading drops, then there is a wiring problem that isn’t visible. Open the harness and visually inspect the wiring for problems. But if the result is the same, then the PCM may be bad.


The OBD2 Code Information Be Applicable For Volkswagen:

2013 Volkswagen e-Co-Motion Concept,2013 Volkswagen Up 4-door,2013 Volkswagen Up,2013 Volkswagen Touareg Edition X,2013 Volkswagen Scirocco GTS,2013 Volkswagen Santana,2013 Volkswagen Polo R WRC,2013 Volkswagen Polo BlueGT,2013 Volkswagen Passat Alltrack,2013 Volkswagen Lavida,2013 Volkswagen Kombi Last Edition,2013 Volkswagen Jetta Hybrid,2013 Volkswagen Golf Sportsvan Concept,2013 Volkswagen Golf Plus Life,2013 Volkswagen Golf Mk VII UK-Version,2013 Volkswagen Golf GTI Cabriolet,2013 Volkswagen Golf,2013 Volkswagen Gol 2-door,2013 Volkswagen Eco Up,2013 Volkswagen Caddy Cross,2012 Volkswagen Tiguan,2012 Volkswagen Jetta GLI,2012 Volkswagen Beetle,2011 Volkswagen eT Concept,2011 Volkswagen e-Up Concept,2011 Volkswagen XL1 Concept,2011 Volkswagen Touran,2011 Volkswagen Touareg,2011 Volkswagen Sharan,2011 Volkswagen Polo GTI,2011 Volkswagen Phaeton,2011 Volkswagen Jetta,2011 Volkswagen Eos,2011 Volkswagen CrossTouran,2011 Volkswagen CrossPolo,2011 Volkswagen CrossGolf,2011 Volkswagen Amarok,2010 Volkswagen Polo,2010 Volkswagen Golf,2009 Volkswagen Phaeton,2009 Volkswagen Golf,2009 Volkswagen Gol,2008 Volkswagen Phaeton,2008 Volkswagen Golf Variant,2008 Volkswagen Golf GTI Concept,2008 Volkswagen Golf BlueMotion,2007 Volkswagen Up Concept,2007 Volkswagen Touran,2007 Volkswagen Touareg,2007 Volkswagen Eos,2006 Volkswagen Rabbit,2006 Volkswagen Passat,2006 Volkswagen Jetta,2006 Volkswagen Eos,2006 Volkswagen CrossPolo,2005 Volkswagen Touareg,2005 Volkswagen Golf,2005 Volkswagen Fox,2004 Volkswagen RaceTouareg,2004 Volkswagen Golf,2004 Volkswagen Concept T,2004 Volkswagen Concept C,2003 Volkswagen Touran,2003 Volkswagen Passat

 

Note:

1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Volkswagen makes.

2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.

3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.

4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.

5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.