Volvo P0031 HO2S Heater Control Circuit Low Bank 1 Sensor 1

Description:

OBD-II Trouble Code Description for P0031 Volvo

HO2S Heater Control Circuit Low

What does this mean?

OBD2 Code P0031 Volvo definition:
A P0031 Volvo DTC (diagnostic trouble code) definition:the O2 sensor (oxygen sensor) located on Bank 1 in front of the catalytic converter. There is also an oxygen sensor behind the converter which is Sensor #2. This O2 sensor #1 may also be refered to as an air/fuel ratio sensor since on some vehicles it is. It detects the amount of oxygen in the exhaust gas compared to the outside air and then vehicle’s computer adjusts the air/fuel ratio going into the engine. The sensor is less effective when the exhaust gas temperature is low, so it includes a heater which is activated to help get better readings from the A/F O2 sensor. Essentially this P0031 Volvo code means that the resistance of the heater circuit is lower than normal. In most cases, that resistance level must fall below 0.8 A to trigger the DTC code. Note, this code is very similar in nature to P0032 Volvo, P0051 Volvo, and P0052 Volvo

Symptoms

Possible sumptoms of OBD code P0031 Volvo
Most likely you’ll not notice any symptoms other than the MIL (malfunction indicator lamp, a.k.a. the check engine light) will illuminate.

Causes

Possible causes of OBD code P0031 Volvo
A P0031 Volvo DTC trouble code may be caused by one or more of the following: A short or open in the heater circuit in the sensor A failed O2 sensor heater Wiring/connectors broken/frayed leading to sensor and/or relay Failed PCM/ECM

Possible Solutions

To fix a P0031 Volvo DTC code, you’ll need to do a proper diagnosis. To do that, you’ll want to inspect the wiring and connectors leading to the sensor. Also if equipped with a heater relay and fuse, you’ll want to check those as well. Use a digital volt ohm meter to: check for 12 volts at the heater circuit feed (hint: unplug the sensor and check at the wiring connector to do this measurement) check the ground circuit for continuity measure the resistance of the heater circuit (done on the sensor itself) measure the resistance and voltage of the wiring Refer to a service manual for the correct specifications (volts, ohms) for your vehicle. On some Toyota vehicles this code is triggered when the resistance of the heater circuit is below 0.8 A. With that said, a common fix for this DTC is to replace the air/fuel (O2 oxygen) sensor #1 on bank 1. Please keep in mind that OEM (original equipment) replacement sensors are recommended (from the dealer). Aftermarket sensors can be less reliable and of poorer quality (not always, but more often). There’s also a chance that replacement parts for the P0031 Volvo code may also fall under a federal emissions warranty (check with your dealer to see if it’s covered).

Related Codes

P0010 Volvo P0011 Volvo P0012 Volvo P0021 Volvo P0022 Volvo


The OBD2 Code Information Be Applicable For Volvo:

2013 Volvo V40,2012 Volvo XC60,2011 Volvo XC90,2011 Volvo V60,2011 Volvo S60,2011 Volvo C30,2010 Volvo S80L,2010 Volvo S80,2010 Volvo C70,2010 Volvo C30,2009 Volvo XC60,2009 Volvo V50,2009 Volvo S60,2009 Volvo S40,2009 Volvo C30,2008 Volvo XC70,2008 Volvo V70,2008 Volvo V50,2008 Volvo S40,2007 Volvo V70,2007 Volvo S80,2007 Volvo S60,2007 Volvo C70,2007 Volvo C30,2006 Volvo XC90,2006 Volvo S80,2006 Volvo C70,2005 Volvo V50,2005 Volvo S60,2004 Volvo XC90,2004 Volvo V70,2004 Volvo V50,2004 Volvo V40,2004 Volvo S40,2003 Volvo V70 R,2003 Volvo S80,2003 Volvo S60 R

Note:

1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Volvo makes.

2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.

3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.

4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.

5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.