Aston Martin P0209 Injector Circuit Malfunction Cylinder 9

Description

OBD-II Trouble Code Description for P0209 Aston Martin

Injector Circuit/Open – Cylinder 9

What does this mean?

OBD2 Code P0209 Aston Martin definition:
P0208 Aston Martin means that the PCM detected a fault in the injector or the wiring to the injector. It monitors the injector and when the injector is activated, the PCM expects to see the voltage pulled “low” or close to zero. When the injector is switched off, the PCM expects to see a voltage that is close to battery voltage or “high”. If it doesn’t see the expected voltage the PCM will set this code. The PCM also monitors resitance in the circuit. If the resistance is excessively low or high it will set this code.

Symptoms

Possible sumptoms of OBD code P0209 Aston Martin
The symptoms for this code will likely be a misfire and a rough running engine. Poor acceleration. The MIL will also be illuminated.

Causes

Possible causes of OBD code P0209 Aston Martin
The causes of a P0208 Aston Martin engine light code could be any of the following: Bad injector. This is usually the cause of this code but doesn’t rule out the possibility of one of the other causes Open in the wiring to the injector Short in the wiring to the injector Bad PCM

Possible Solutions

First, using a DVOM check the resistance of the injector. If it isn’t within specs, then replace the injector. Check for voltage at the fuel injector connector. It should have 10 volts or more. Visually check the connector for damage or broken wires. Visually check the injector for damage. If you have access to an injector tester, activate the injector and see if it operates. If the injector operates, then you likely have either an open in the wiring, or a blocked injector. If you do not have access to a tester, swap the injector with another one and see if the code changes. If the code changes, then change the injector. At the PCM, remove the driver wire from the PCM connector and Ground the wire. (Make sure you have the correct wire. If you’re not sure, do not attempt) The injector should activate Replace the injector First, using a DVOM check the resistance of the injector. If it isn’t within specs, then replace the injector. Check for voltage at the fuel injector connector. It should have 10 volts or more. Visually check the connector for damage or broken wires. Visually check the injector for damage. If you have access to an injector tester, activate the injector and see if it operates. If the injector operates, then you likely have either an open in the wiring, or a blocked injector. If you do not have access to a tester, swap the injector with another one and see if the code changes. If the code changes, then change the injector. At the PCM, remove the driver wire from the PCM connector and Ground the wire. (Make sure you have the correct wire. If you’re not sure, do not attempt) The injector should activate Replace the injector

The OBD2 Code Information Be Applicable For Aston Martin:

2014 Aston Martin Vanquish Volante,2014 Aston Martin V12 Vantage S,2014 Aston Martin Rapide S,2013 Aston Martin Vantage SP10,2013 Aston Martin Vanquish Q,2013 Aston Martin Vanquish Centenary Edition,2013 Aston Martin V12 Zagato,2013 Aston Martin V12 Vantage Roadster,2013 Aston Martin DB9,2013 Aston Martin CC100 Speedster Concept,2013 Aston Martin AM 310 Vanquish,2012 Aston Martin Virage Volante,2012 Aston Martin Virage,2012 Aston Martin Vantage GT3,2012 Aston Martin V8 Vantage S Roadster,2012 Aston Martin V8 Vantage S,2012 Aston Martin V8 Vantage,2012 Aston Martin Cygnet,2011 Aston Martin Vantage GT4,2011 Aston Martin V8 Vantage N420 Roadster,2011 Aston Martin V8 Vantage N420,2011 Aston Martin V12 Zagato Racecar,2011 Aston Martin V12 Zagato Concept,2011 Aston Martin DBS Carbon Edition,2011 Aston Martin DB9,2010 Aston Martin V12 Vantage,2010 Aston Martin Rapide,2010 Aston Martin One-77,2010 Aston Martin DBS Volante,2009 Aston Martin Vantage GT4,2009 Aston Martin V8 Vantage Roadster,2009 Aston Martin V8 Vantage,2009 Aston Martin Lagonda Concept,2009 Aston Martin DB9 Volante,2009 Aston Martin DB9,2009 Aston Martin Cygnet Concept,2008 Aston Martin V8 Vantage N400,2008 Aston Martin DBS Racing Green,2008 Aston Martin DBS Lightning Silver,2008 Aston Martin DBS Infa Red,2008 Aston Martin DBS,2008 Aston Martin DB9 LM,2007 Aston Martin V8 Vantage Roadster,2007 Aston Martin V8 Vantage N24,2007 Aston Martin V8 Vantage,2007 Aston Martin V12 Vantage RS Concept,2007 Aston Martin DBS,2007 Aston Martin DB9 Volante,2007 Aston Martin DB9,2006 Aston Martin Rapide Concept,2006 Aston Martin DBRS9,2005 Aston Martin V8 Vantage,2005 Aston Martin DBR9,2004 Aston Martin Zagato Vanquish Roadster Concept,2004 Aston Martin Vanquish S V12,2004 Aston Martin DBR9 Prototype,2004 Aston Martin DB9 Volante,2004 Aston Martin DB9,2003 Aston Martin DB AR1,2003 Aston Martin DB7 GT,2003 Aston Martin AMV8 Concept Car,2002 Aston Martin DB7 Vantage Zagato

 

Note:

1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Aston Martin.

2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.

3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.

4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.

5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.