Description
OBD-II Trouble Code Description for P0453 Buick
Evaporative Emission System Pressure Sensor/Switch High
What does this mean?
OBD2 Code P0453 Buick definition:
The EVAP (Evaporative Emissions) System allows fuel tank vapors to be purged into the engine and burnt rather than expelled into the atmosphere as harmful emissions. The EVAP system contains a pressure sensor to check the integrity of the system. Periodically, the EVAP system performs a pressure test to check that there are no leaks in the system. It uses this sensor, also known as a fuel tank pressure (FTP) sensor to check for leaks. Basically P0453 Buick means the PCM (Powertrain Control Module) noticed the EVAP Pressure sensor or FTP is indicating a higher than normal pressure (above 4.5 Volts) in the EVAP system. NOTE: On some vehicles the FTP is a part of the fuel pump assembly in the tank.
Symptoms
Possible sumptoms of OBD code P0453 Buick
There will likely be no noticeable symptoms along with this code other than the MIL (Malfunction Indicator Lamp), commonly known as Check Engine Light illumination. However, there may be noticeable fuel odors in some cases.
Causes
Possible causes of OBD code P0453 Buick
A P0453 Buick DTC trouble code may be caused by one or more of the following: Open on FTP sensor signal wire Short to voltage on FTP sensor signal wire Bad FTP sensor Abnormally high pressure in fuel tank due to blockage in EVAP purge hoses or overfilled tank Loose/damaged FTP sensor connector Loss of ground to the sensor
Possible Solutions
Using an scan tool access FTP sensor value with Key on Engine off (KOEO). Normal value is usually somewhere near 2.5 Volts at atmospheric pressure (may fluctuate some due to altitude). It shouldn’t ever be above 4.5 Volts. 1) If it is close to 2.7V with the gas cap off, the problem is likely intermittent. Using a Digital Volt Ohm Meter, measure the voltage on the signal wire while trying to induce the problem by wiggle testing all the wiring at the FTP sensor. If the voltage fluctuates when wiggle testing, check for connector problems; i.e. water in the connector, broken or chafed wiring. 2) If the value shown on the scan tool is above 4.5V, unplug the sensor (if possible) and check for voltage again. If the high voltage is still present when unplugged, inspect wiring harness for a short to voltage on the signal wire. If the high voltage disappears when unplugging the sensor, check for a good ground to the sensor and proper reference voltage. If you have a good ground and 5 Volts reference voltage, replace the FTP sensor since it’s likely shorted out.
The OBD2 Code Information Be Applicable For Buick
2013 Buick Verano Turbo,2013 Buick Riviera Concept,2013 Buick Encore,2013 Buick Enclave,2012 Buick Verano,2012 Buick Regal GS,2011 Buick Regal,2011 Buick LaCrosse GL Concept,2011 Buick GL8,2011 Buick Envision Concept,2010 Buick Regal GS Concept,2010 Buick LaCrosse,2009 Buick Business Concept,2008 Buick Lucerne Super,2008 Buick LaCrosse Super,2008 Buick LaCrosse CXS,2008 Buick Invicta Concept,2008 Buick Enclave,2007 Buick Riviera Concept Coupe,2006 Buick Terraza,2006 Buick Rendezvous CXL,2006 Buick Rainier CXL,2006 Buick Lucerne CXS,2006 Buick Enclave Concept,2005 Buick Terraza CXL,2005 Buick Royaum,2005 Buick Rendezvous CX,2005 Buick Park Avenue,2005 Buick LeSabre Celebration Edition,2005 Buick LaCrosse CXS,2005 Buick LaCrosse CSX,2005 Buick Century,2004 Buick Velite Concept,2004 Buick Rendezvous Ultra,2004 Buick Regal Abboud GS,2004 Buick Rainier,2004 Buick Park Avenue Ultra,2003 Buick Rendezvous,2003 Buick Park Avenue Ultra,2002 Buick Rendezvous,2002 Buick Regal,2002 Buick LeSabre Custom,2001 Buick Regal,2001 Buick Park Avenue Ultra,2001 Buick Park Avenue,2001 Buick LeSabre,2001 Buick Blackhawk Concept,2001 Buick 2-2 Bengal Roadster Concept,2000 Buick Regal GNX Show Car,2000 Buick Regal Cielo Concept,2000 Buick Regal,2000 Buick Park Avenue,2000 Buick LeSabre Limited,2000 Buick Century
Note:
1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Buick makes.
2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.
3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.
4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.
5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.