Description
OBD-II Trouble Code Description for P0211 Chrysler
Injector Circuit/Open – Cylinder 11
What does this mean?
OBD2 Code P0211 Chrysler definition:
P0210 Chrysler means that the PCM detected a fault in the injector or the wiring to the injector. It monitors the injector and when the injector is activated, the PCM expects to see the voltage pulled “low” or close to zero. When the injector is switched off, the PCM expects to see a voltage that is close to battery voltage or “high”. If it doesn’t see the expected voltage the PCM will set this code. The PCM also monitors resitance in the circuit. If the resistance is excessively low or high it will set this code.
Symptoms
Possible sumptoms of OBD code P0211 Chrysler
The symptoms for this code will likely be a misfire and a rough running engine. Poor acceleration. The MIL will also be illuminated.
Causes
Possible causes of OBD code P0211 Chrysler
The causes of a P0210 Chrysler engine light code could be any of the following: Bad injector. This is usually the cause of this code but doesn’t rule out the possibility of one of the other causes Open in the wiring to the injector Short in the wiring to the injector Bad PCM
Possible Solutions
First, using a DVOM check the resistance of the injector. If it isn’t within specs, then replace the injector. Check for voltage at the fuel injector connector. It should have 10 volts or more. Visually check the connector for damage or broken wires. Visually check the injector for damage. If you have access to an injector tester, activate the injector and see if it operates. If the injector operates, then you likely have either an open in the wiring, or a blocked injector. If you do not have access to a tester, swap the injector with another one and see if the code changes. If the code changes, then change the injector. At the PCM, remove the driver wire from the PCM connector and Ground the wire. (Make sure you have the correct wire. If you’re not sure, do not attempt) The injector should activate Replace the injector First, using a DVOM check the resistance of the injector. If it isn’t within specs, then replace the injector. Check for voltage at the fuel injector connector. It should have 10 volts or more. Visually check the connector for damage or broken wires. Visually check the injector for damage. If you have access to an injector tester, activate the injector and see if it operates. If the injector operates, then you likely have either an open in the wiring, or a blocked injector. If you do not have access to a tester, swap the injector with another one and see if the code changes. If the code changes, then change the injector. At the PCM, remove the driver wire from the PCM connector and Ground the wire. (Make sure you have the correct wire. If you’re not sure, do not attempt) The injector should activate Replace the injector
The OBD2 Code Information Be Applicable For Chrysler:
2013 Chrysler Town and Country S,2013 Chrysler 300 Motown Edition,2013 Chrysler 300 Glacier,2012 Chrysler Ypsilon,2012 Chrysler Delta,2012 Chrysler 300 SRT8,2012 Chrysler 300 Luxury Series,2012 Chrysler 300C,2011 Chrysler Town and Country,2011 Chrysler 300,2011 Chrysler 200 S,2011 Chrysler 200 Convertible,2011 Chrysler 200,2009 Chrysler GEM Peapod,2009 Chrysler 200C EV Concept,2008 Chrysler ecoVoyager Concept,2008 Chrysler Town and Country,2008 Chrysler Sebring Convertible,2008 Chrysler EV Concept,2008 Chrysler 300C UK Version,2008 Chrysler 300C Touring UK Version,2008 Chrysler 300C Touring SRT UK Version,2008 Chrysler 300C SRT UK Version,2007 Chrysler Sebring UK Version,2007 Chrysler Sebring,2007 Chrysler Pacifica,2007 Chrysler PT Street Cruiser Pacific Coast Highway,2007 Chrysler Nassau Concept,2007 Chrysler Crossfire UK Version,2007 Chrysler Crossfire Roadster UK Version,2007 Chrysler Aspen,2006 Chrysler Imperial Concept,2006 Chrysler 300C SRT8 Touring,2006 Chrysler 300C Heritage Edition,2005 Chrysler Town and Country,2005 Chrysler PT Cruiser Convertible,2005 Chrysler Firepower Concept,2005 Chrysler Crossfire SRT6 Roadster,2005 Chrysler Crossfire SRT6,2005 Chrysler Crossfire Roadster,2005 Chrysler Akino Concept,2005 Chrysler 300C Touring,2005 Chrysler 300C SRT8,2005 Chrysler 300C,2005 Chrysler 300,2004 Chrysler Pacifica,2004 Chrysler ME FourTwelve Concept,2004 Chrysler Crossfire,2003 Chrysler Airflite Concept,2003 Chrysler 300M,2003 Chrysler 300C Touring Concept,2003 Chrysler 300C Concept,2002 Chrysler Pacifica Concept,2002 Chrysler California Cruiser Concept
Note:
1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Chrysler makes.
2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.
3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.
4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.
5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.