Description
OBD-II Trouble Code Description for P0106 Alfa Romeo
Manifold Absolute Pressure/Barometric Pressure Circuit Range/Performance
What does this mean?
OBD2 Code P0106 Alfa Romeo definition:
The Powertrain Control Module (PCM) uses the Manifold Absolute Pressure Sensor (MAP) to monitor engine load. (NOTE: Some vehicles have a Barometric Pressure (BARO) sensor that is integral to the Mass Air Flow (MAF) sensor and do not have a MAP sensor. Other vehicles have a MAF/BARO and a redundant MAP sensor where the MAP sensor functions as a backup input in case of MAF failure.) The PCM supplies a 5 Volt reference signal to the MAP sensor. Usually the PCM also supplies a ground circuit to the MAP sensor as well. As the manifold pressure changes with load, the MAP sensor input informs the PCM. At idle the voltage should be 1 to 1.5 Volts and approximately 4.5 Volts at Wide Open Throttle (WOT). The PCM looks for any change in manifold pressure to be preceded by a change in engine load in the form of changes in throttle angle, engine speed, or Exhaust Gas Recirculation (EGR) flow. If the PCM doesn’t see any of these factors change while detecting a rapid change in MAP value, it will set a P0106 Alfa Romeo.
Symptoms
Possible sumptoms of OBD code P0106 Alfa Romeo
Engine runs rough Black smoke at tailpipe Engine will not idle Poor fuel economy Engine misses at speed
Causes
Possible causes of OBD code P0106 Alfa Romeo
Bad MAP sensor Water/dirt intrusion affecting MAP sensor connector Intermittent open in the reference, ground, or signal wire for the MAP sensor Intermittent short in the reference, ground, or signal wire for the MAP sensor Ground problem due to corrosion causing intermittent signal problem A break in the flexible air intake duct between the MAF and the intake manifold Bad PCM (do not assume the PCM is bad until you’ve exhausted all other possibilities)
Possible Solutions
Using a scan tool, watch the MAP sensor value with the key on, engine off. Compare the BARO reading with the MAP reading. They should be roughly equal. The voltage for the MAP sensor should read approx. 4.5 volts. Now start the engine and look for a significant drop in the MAP sensor voltage indicating the MAP sensor is working. If the MAP reading doesn’t change perform the following: With the Key on, engine off, disconnect the vacuum hose from the MAP sensor. Using a vacuum pump, pull 20 in. of vacuum on the MAP sensor. Does the voltage drop? It should. If it doesn’t inspect the MAP sensor vacuum port and vacuum hose to manifold for a restriction of some kind. Repair or replace as necessary. If there are no restrictions, and the value doesn’t change with vacuum, then perform the following: with the Key on and engine off and the MAP sensor unplugged, check for 5 Volts at the reference wire to the MAP sensor connector with a Digital Voltmeter. If there is none, check for reference voltage at the PCM connector. If the reference voltage is present at the PCM connector but not the MAP connector, check for open or short in the reference wire between MAP and PCM and retest. If reference voltage is present, then check for existing ground at the MAP sensor connector. If it isn’t present then repair open/short in the ground circuit. If ground is present, then replace MAP sensor.
The OBD2 Code Information Be Applicable For Alfa Romeo:
2014 Alfa Romeo MiTo new,,2014 Alfa Romeo Giulietta new,,2014 Alfa Romeo 4C,,2013 Alfa Romeo Gloria Concept,,2013 Alfa Romeo Disco Volante Touring,,2012 Alfa Romeo Disco Volante Touring Concept,,2011 Alfa Romeo TZ3 Stradale,,2011 Alfa Romeo Giulietta,,2011 Alfa Romeo 4C Concept,,2010 Alfa Romeo TZ3 Corsa,,2010 Alfa Romeo Pandion Concept,,2010 Alfa Romeo MiTo Quadrifoglio Verde,,2010 Alfa Romeo MiTo 1.4 MultiAir,,2010 Alfa Romeo 2uettottanta Concept,,2010 Alfa Romeo 159 1750 TBi,,2009 Alfa Romeo MiTo UK Version,,2009 Alfa Romeo MiTo GTA Concept,,2009 Alfa Romeo Mi.To,,2009 Alfa Romeo Brera S,,2009 Alfa Romeo 8C Spider,,2009 Alfa Romeo 159 Sportwagon,,2009 Alfa Romeo 159,,2007 Alfa Romeo GT Q2,,2007 Alfa Romeo 8c Competizione,,2007 Alfa Romeo 147 Q2,,2007 Alfa Romeo 147 Murphy and Nye,,2007 Alfa Romeo 147 CnC,,2006 Alfa Romeo Spider UK Version,,2006 Alfa Romeo Spider,,2006 Alfa Romeo 159 Sportwagon,,2005 Alfa Romeo Brera UK Version,,2005 Alfa Romeo Brera,,2005 Alfa Romeo 159,,2004 Alfa Romeo Visconti Concept ItalDesign,,2004 Alfa Romeo 8C Competizione,,2004 Alfa Romeo 166,,2004 Alfa Romeo 156 GTA Autodelta,,2004 Alfa Romeo 156 Crosswagon Q4,,2004 Alfa Romeo 156 Crosswagon,,2004 Alfa Romeo 147 5door,,2004 Alfa Romeo 147 3door,,2003 Alfa Romeo Spider,,2003 Alfa Romeo Kamal Concept,,2003 Alfa Romeo GTV,,2003 Alfa Romeo GT,,2003 Alfa Romeo 156 Sportwagon 2.0 JTD,,2003 Alfa Romeo 156 GTA Autodelta,,2003 Alfa Romeo 156 2.4 JTD,,2003 Alfa Romeo 147 TI,,2002 Alfa Romeo 147 JTD 16V,,2002 Alfa Romeo 147 GTA
Note:
1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Alfa Romeo makes.
2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.
3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.
4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.
5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.