Description
OBD-II Trouble Code Description for P0108 Alfa Romeo
Manifold Absolute Pressure/Barometric Pressure Circuit High Input
What does this mean?
OBD2 Code P0108 Alfa Romeo definition:
The MAP (Manifold Absolute Pressure) sensor measures engine manifold negative air pressure. It’s usually a three wire sensor: a ground wire, a 5 volt reference wire from the PCM (Powertrain Control Module) to the MAP sensor, and a signal wire that informs the PCM of the MAP sensor voltage reading as it changes. The higher the engine vacuum, the lower the voltage reading. The voltage should range between about 1 volt (at idle) to about 5 volts (WOT wide open throttle). If the PCM sees the voltage reading from the MAP sensor is greater than 5 Volts, or if the voltage reading is higher than what the PCM considers normal under certain circumstances, a P0108 Alfa Romeo DTC will set.
Symptoms
Possible sumptoms of OBD code P0108 Alfa Romeo
MIL (Malfunction Indicator Lamp) will likely be on Engine may run poorly Engine may not run at all Fuel mileage may decrease Presence of black smoke at exhaust
Causes
Possible causes of OBD code P0108 Alfa Romeo
Bad MAP sensor Leak in vacuum supply line to MAP sensor Engine vacuum leak Short on signal wire to PCM Short on reference voltage wire from PCM Open in ground circuit to MAP Worn engine causing low vacuum
Possible Solutions
A good way to diagnose if the MAP sensor is to blame would be to compare the KOEO (key on engine off) MAP sensor reading on a scan tool with the Barometric pressure reading. They should be the same because they both measure atmospheric pressure. If the MAP reading is greater than 0.5 volt off of the BARO reading, then replacing the MAP sensor would likely fix the problem. Otherwise, start the engine and observe the MAP reading at idle. It should normally be about 1.5 volts (varies according to altitude). a. If it is, the problem is likely intermittent. Check all the vacuum hoses for damage and replace as necessary. You can also try wiggle testing the harness and connector to reproduce the problem. b. If the scan tool MAP reading is more than 4.5 volts, check the actual engine vacuum reading with the engine running. If it is less than 15 or 16 in. Hg, then the PCM is probably not seeing enough vacuum (due to a worn engine, perhaps) for a given operating condition (which causes a higher than normal voltage signal to the PCM) and setting the code. Repair the engine vacuum problem and retest. c. But, if the actual engine vacuum reading is 16 in. Hg or more, then unplug the MAP sensor. The scan tool MAP reading should indicate that there is no voltage present. Check that the ground from the PCM is intact and also that the MAP sensor connector and terminals are tight. If the connection is good, then replace the map sensor. d. However if, with KOEO, & the MAP sensor unplugged, the scan tool shows a voltage reading, then there may be a short in the harness to the MAP sensor. Turn the ignition off. At the PCM unplug connector and remove the MAP signal wire from the connector. Re-attach the PCM connector and see if with KOEO, the scan tool MAP reading shows voltage. If it still does, replace the PCM. If not, check for voltage on the signal wire you just removed from the PCM. If there is voltage on the signal wire, find the short in the harness and repair.
The OBD2 Code Information Be Applicable For Alfa Romeo:
2014 Alfa Romeo MiTo new,,2014 Alfa Romeo Giulietta new,,2014 Alfa Romeo 4C,,2013 Alfa Romeo Gloria Concept,,2013 Alfa Romeo Disco Volante Touring,,2012 Alfa Romeo Disco Volante Touring Concept,,2011 Alfa Romeo TZ3 Stradale,,2011 Alfa Romeo Giulietta,,2011 Alfa Romeo 4C Concept,,2010 Alfa Romeo TZ3 Corsa,,2010 Alfa Romeo Pandion Concept,,2010 Alfa Romeo MiTo Quadrifoglio Verde,,2010 Alfa Romeo MiTo 1.4 MultiAir,,2010 Alfa Romeo 2uettottanta Concept,,2010 Alfa Romeo 159 1750 TBi,,2009 Alfa Romeo MiTo UK Version,,2009 Alfa Romeo MiTo GTA Concept,,2009 Alfa Romeo Mi.To,,2009 Alfa Romeo Brera S,,2009 Alfa Romeo 8C Spider,,2009 Alfa Romeo 159 Sportwagon,,2009 Alfa Romeo 159,,2007 Alfa Romeo GT Q2,,2007 Alfa Romeo 8c Competizione,,2007 Alfa Romeo 147 Q2,,2007 Alfa Romeo 147 Murphy and Nye,,2007 Alfa Romeo 147 CnC,,2006 Alfa Romeo Spider UK Version,,2006 Alfa Romeo Spider,,2006 Alfa Romeo 159 Sportwagon,,2005 Alfa Romeo Brera UK Version,,2005 Alfa Romeo Brera,,2005 Alfa Romeo 159,,2004 Alfa Romeo Visconti Concept ItalDesign,,2004 Alfa Romeo 8C Competizione,,2004 Alfa Romeo 166,,2004 Alfa Romeo 156 GTA Autodelta,,2004 Alfa Romeo 156 Crosswagon Q4,,2004 Alfa Romeo 156 Crosswagon,,2004 Alfa Romeo 147 5door,,2004 Alfa Romeo 147 3door,,2003 Alfa Romeo Spider,,2003 Alfa Romeo Kamal Concept,,2003 Alfa Romeo GTV,,2003 Alfa Romeo GT,,2003 Alfa Romeo 156 Sportwagon 2.0 JTD,,2003 Alfa Romeo 156 GTA Autodelta,,2003 Alfa Romeo 156 2.4 JTD,,2003 Alfa Romeo 147 TI,,2002 Alfa Romeo 147 JTD 16V,,2002 Alfa Romeo 147 GTA
Note:
1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Alfa Romeo makes.
2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.
3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.
4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.
5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.