Aston Martin P0150 Air Fuel Ratio Circuit Bank 2 Sensor 1

Description

OBD-II Trouble Code Description for P0150 Aston Martin

O2 Sensor Circuit

What does this mean?

OBD2 Code P0150 Aston Martin definition:
The O2 sensor produces a voltage based on oxygen content in the exhaust. The voltage varies between .1 and .9 Volts, .1 indicating lean and .9 indicating rich. The ECM constantly monitors this voltage while in closed loop to determine how much fuel to inject. If the ECM determines that the O2 sensor voltage was too low (less than .4 Volts) for too long (for more than 20 seconds (time varies with model)), this code is set. The code P0150 Aston Martin definition:Bank 2.

Symptoms

Possible sumptoms of OBD code P0150 Aston Martin
Depending if the problem is intermittent or not, there may be no symptoms other than MIL (malfunction indicator lamp) illumination. If the problem is constant, then symptoms may include one or more of the following: MIL illumination Engine runs rough, missing or stumbling Blows black smoke from tail pipe Engine dies Poor fuel economy

Causes

Possible causes of OBD code P0150 Aston Martin
Usually the cause of P0150 Aston Martin is a bad oxygen sensor, however this isn’t always the case. If your o2 sensors haven’t been replaced and they are old, it’s a good bet that the sensor is the problem. But, It could be caused by any of the following: Water or corrosion in the connector Loose terminals in the connector Wiring burnt on exhaust components Open or short in the wiring due to rubbing on engine components Holes in exhaust allowing unmetered oxygen into exhaust system Unmetered vacuum leak at the engine Bad o2 sensor Bad PCM

Possible Solutions

Using a scan tool, determine if the Bank 2, sensor 1 is switching properly. It should switch rapidly between rich and lean, evenly. 1. If it does, the problem is likely intermittent and you should examine the wiring for any visible damage. Then perform a wiggle test by manipulating the connector and wiring while watching the o2 sensor voltage. If it drops out, fix the appropriate part of the wiring harness where problem resides. 2. If it doesn’t switch properly, try to determine if the sensor is accurately reading the exhaust or not. Do this by removing the fuel pressure regulator vacuum supply briefly. The o2 sensor reading should go rich, reacting to the extra fuel added. Reinstall regulator supply. Then induce a lean condition by removing a vacuum supply line from the intake manifold. The o2 sensor reading should go lean, reacting to the enleaned exhaust. If the sensor operates properly, then the sensor may be okay and the problem may be holes in the exhaust or an unmetered vacuum leak in the engine (NOTE: Unmetered vacuum leaks at the engine are almost always accompanied by lean codes. Refer to the appropriate articles for diagnosing an unmetered vacuum leak). If the exhaust does have holes in it, it’s possible that the o2 sensor may be misreading the exhaust because of the extra oxygen entering the pipe via those holes 3. If none of this is the case and the o2 sensor just isn’t switching or acts sluggish, unplug the sensor and make sure there is 5 Volt reference voltage to the sensor. Then check for 12V supply to the o2 sensor’s heater circuit. Also check for continuity to ground on the ground circuit. If any of these are missing, or aren’t their proper voltage, repair open or short in the appropriate wire. The o2 sensor will not operate properly without proper voltage. If the proper voltages are present, replace the o2 sensor.

The OBD2 Code Information Be Applicable For Aston Martin:

2014 Aston Martin Vanquish Volante,2014 Aston Martin V12 Vantage S,2014 Aston Martin Rapide S,2013 Aston Martin Vantage SP10,2013 Aston Martin Vanquish Q,2013 Aston Martin Vanquish Centenary Edition,2013 Aston Martin V12 Zagato,2013 Aston Martin V12 Vantage Roadster,2013 Aston Martin DB9,2013 Aston Martin CC100 Speedster Concept,2013 Aston Martin AM 310 Vanquish,2012 Aston Martin Virage Volante,2012 Aston Martin Virage,2012 Aston Martin Vantage GT3,2012 Aston Martin V8 Vantage S Roadster,2012 Aston Martin V8 Vantage S,2012 Aston Martin V8 Vantage,2012 Aston Martin Cygnet,2011 Aston Martin Vantage GT4,2011 Aston Martin V8 Vantage N420 Roadster,2011 Aston Martin V8 Vantage N420,2011 Aston Martin V12 Zagato Racecar,2011 Aston Martin V12 Zagato Concept,2011 Aston Martin DBS Carbon Edition,2011 Aston Martin DB9,2010 Aston Martin V12 Vantage,2010 Aston Martin Rapide,2010 Aston Martin One-77,2010 Aston Martin DBS Volante,2009 Aston Martin Vantage GT4,2009 Aston Martin V8 Vantage Roadster,2009 Aston Martin V8 Vantage,2009 Aston Martin Lagonda Concept,2009 Aston Martin DB9 Volante,2009 Aston Martin DB9,2009 Aston Martin Cygnet Concept,2008 Aston Martin V8 Vantage N400,2008 Aston Martin DBS Racing Green,2008 Aston Martin DBS Lightning Silver,2008 Aston Martin DBS Infa Red,2008 Aston Martin DBS,2008 Aston Martin DB9 LM,2007 Aston Martin V8 Vantage Roadster,2007 Aston Martin V8 Vantage N24,2007 Aston Martin V8 Vantage,2007 Aston Martin V12 Vantage RS Concept,2007 Aston Martin DBS,2007 Aston Martin DB9 Volante,2007 Aston Martin DB9,2006 Aston Martin Rapide Concept,2006 Aston Martin DBRS9,2005 Aston Martin V8 Vantage,2005 Aston Martin DBR9,2004 Aston Martin Zagato Vanquish Roadster Concept,2004 Aston Martin Vanquish S V12,2004 Aston Martin DBR9 Prototype,2004 Aston Martin DB9 Volante,2004 Aston Martin DB9,2003 Aston Martin DB AR1,2003 Aston Martin DB7 GT,2003 Aston Martin AMV8 Concept Car,2002 Aston Martin DB7 Vantage Zagato

 

Note:

1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Aston Martin.

2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.

3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.

4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.

5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.