Description
OBD-II Trouble Code Description for P0403 Chrysler
Exhaust Gas Recirculation Control Circuit
What does this mean?
OBD2 Code P0403 Chrysler definition:
The Exhaust Gas Recirculation (EGR) system is controlled by a vacuum solenoid. The solenoid is supplied ignition voltage. The Powertrain Control Module (PCM) controls the vacuum solenoid by grounding the control circuit(ground) or driver. The primary function of the driver is to supply ground for the object that is being controlled. Each driver has a fault circuit that the PCM monitors. When the PCM turns a component on, the control circuit voltage is low, or close to zero. When the component is turned off, the voltage on the control circuit is high, or near battery voltage. The PCM watches for these conditions, and if it doesn’t see the proper voltage at the proper time, this code is set.
Symptoms
Possible sumptoms of OBD code P0403 Chrysler
Usually a fault in the control circuit, will leave no noticeable symptoms other than the Malfunction Indicator Lamp (MIL) illumination. However, if the EGR control solenoid is stuck open due to debris, etc. the code may be accompanied by misfire under acceleration, rough idle, or engine dying altogether.
Causes
Possible causes of OBD code P0403 Chrysler
The causes for a P0403 Chrysler EGR code could be any of the following: Bad EGR solenoid Excessive resistance in control circuit (PCM controlled ground) due to an open, chafing or damage to the harness Poor connection at the EGR solenoid harness (worn or loose pins) Water intrusion at the EGR solenoid harness Blockage in EGR control solenoid holding solenoid open or closed causing excessive resistance Loss of supply voltage to EGR solenoid Bad PCM
Possible Solutions
With the ignition on and engine off, use a scan tool to activate the EGR solenoid. Listen or feel for a clicking, indicating that the solenoid is operating. If the solenoid does operate, you’ll have to check current draw on the ground circuit. It should be less than one amp. If it is then the problem is intermittent. If it isn’t then there is excessive resistance in the circuit and perform the following 1. When it’s activated see if you can blow lightly through it. IF you can’t there may be a blockage causing excessive resistance. Replace EGR solenoid as needed. If there is no blockage, disconnect the EGR solenoid and the PCM connector containing the EGR solenoid control circuit. Using a digital Volt-Ohm meter (DVOM) check resistence between the control circuit and battery ground. It should be infinite. If it isn’t, then there is a short to ground on the control circuit. Repair the short to ground and retest as needed. 2. If the solenoid doesn’t click as it should, disconnect the EGR solenoid connector and connect a test light between the two wires. Using the scan tool, command the EGR solenoid on. The light should light up. If it does, replace the EGR solenoid. If it does not perform the following: a. Check for 12 Volts on the ignition supply voltage to the solenoid. If it isn’t present, inspect the supply circuit for an open, or a short due to chafing or breakage and re-test. b. If it still doesn’t operate: then manually ground the EGR solenoid control circuit. The light should light. If it does, repair open in EGR solenoid control circuit and re-test. If it doesn’t, replace EGR solenoid.
The OBD2 Code Information Be Applicable For Chrysler:
2013 Chrysler Town and Country S,2013 Chrysler 300 Motown Edition,2013 Chrysler 300 Glacier,2012 Chrysler Ypsilon,2012 Chrysler Delta,2012 Chrysler 300 SRT8,2012 Chrysler 300 Luxury Series,2012 Chrysler 300C,2011 Chrysler Town and Country,2011 Chrysler 300,2011 Chrysler 200 S,2011 Chrysler 200 Convertible,2011 Chrysler 200,2009 Chrysler GEM Peapod,2009 Chrysler 200C EV Concept,2008 Chrysler ecoVoyager Concept,2008 Chrysler Town and Country,2008 Chrysler Sebring Convertible,2008 Chrysler EV Concept,2008 Chrysler 300C UK Version,2008 Chrysler 300C Touring UK Version,2008 Chrysler 300C Touring SRT UK Version,2008 Chrysler 300C SRT UK Version,2007 Chrysler Sebring UK Version,2007 Chrysler Sebring,2007 Chrysler Pacifica,2007 Chrysler PT Street Cruiser Pacific Coast Highway,2007 Chrysler Nassau Concept,2007 Chrysler Crossfire UK Version,2007 Chrysler Crossfire Roadster UK Version,2007 Chrysler Aspen,2006 Chrysler Imperial Concept,2006 Chrysler 300C SRT8 Touring,2006 Chrysler 300C Heritage Edition,2005 Chrysler Town and Country,2005 Chrysler PT Cruiser Convertible,2005 Chrysler Firepower Concept,2005 Chrysler Crossfire SRT6 Roadster,2005 Chrysler Crossfire SRT6,2005 Chrysler Crossfire Roadster,2005 Chrysler Akino Concept,2005 Chrysler 300C Touring,2005 Chrysler 300C SRT8,2005 Chrysler 300C,2005 Chrysler 300,2004 Chrysler Pacifica,2004 Chrysler ME FourTwelve Concept,2004 Chrysler Crossfire,2003 Chrysler Airflite Concept,2003 Chrysler 300M,2003 Chrysler 300C Touring Concept,2003 Chrysler 300C Concept,2002 Chrysler Pacifica Concept,2002 Chrysler California Cruiser Concept
Note:
1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Chrysler makes.
2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.
3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.
4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.
5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.