Description
OBD-II Trouble Code Description for P0107 Citroen
Manifold Absolute Pressure/Barometric Pressure Circuit Low Input
What does this mean?
OBD2 Code P0107 Citroen definition:
The Manifold Absolute Pressure (MAP) sensor responds to changes in the intake manifold pressure (vacuum). 5 Volts is supplied to the sensor from the PCM (powertrain control module). Inside the MAP sensor is a resistor that moves in relation to manifold pressure. The resistor varies the voltage between about 1 volt to 4.5 volts (depending on engine load) and that voltage signal is returned to the PCM to indicate manifold pressure (vacuum). This signal is essential for the PCM to determine fuel delivery. A P0107 Citroen DTC is set when the PCM sees that the MAP signal voltage is less than .25 volts which is too low.
Symptoms
Possible sumptoms of OBD code P0107 Citroen
Anytime the MAP sensor signal is low the vehicle will likely have a very difficult time starting. Other symptoms may include: Hard to start Long cranking times Sputtering/missing Blowing black smoke Poor fuel economy Dies intermittently MIL(Malfunction Indicator Lamp) illumination
Causes
Possible causes of OBD code P0107 Citroen
Bad MAP sensor Open or short in the signal circuit Open or short in the 5 Volt reference circuit Ground circuit open or shorted Bad PCM
Possible Solutions
First, using a scan tool with the Key on and engine running, monitor the MAP sensor voltage. If it is reading less than .5 volts, turn engine off, unplug the MAP sensor and, using a DVOM (Digital Volt/Ohm Meter) check for 5Volts on the 5 Volt reference circuit. 1. If there is not 5 Volts on the reference circuit, then check for the reference voltage at the PCM connector. If it is present at the PCM connector but not the MAP connector, repair the open in the reference circuit between the PCM and MAP harness connector. If 5 Volt reference is NOT present at the PCM connector, check powers and grounds of PCM and repair/replace as needed. (NOTE: On Chrysler products, a shorted Crank sensor, Vehicle speed sensor or any other sensor that utilizes the 5 Volt reference from the PCM can short out the 5 Volt reference. To fix simply unplug each sensor one at a time until the 5 Volt reference reappears. The last sensor unplugged is the shorted sensor.) 2. If you have a 5 Volt reference at the MAP connector, jumper the 5 volt reference circuit to the signal circuit. Now check the MAP voltage on the scan tool. It should be 4.5 to 5 Volts. If it is, replace MAP sensor. If not, repair open/short in the signal circuit wiring and re-check. 3. If all appears okay, perform a wiggle test. Start engine and manipulate the harness, connector and tap on the MAP sensor. Note any changes in voltage or engine speed. Repair connector, harness, or sensor as needed. 4. If the wiggle test checks out, use a vacuum pump (or just use your lungs) to draw a vacuum on the MAP sensor vacuum port. As you add vacuum the voltage should decrease. With no vacuum, the MAP sensor should read approximately 4.5 volts. If there is no change in MAP sensor reading on the scan tool, replace MAP sensor.
The OBD2 Code Information Be Applicable For Citroen :
2013 Citroen Technospace Concept,2013 Citroen DS Wild Rubis Concept,2013 Citroen DS3 Cabrio Racing Concept,2013 Citroen Cactus Concept,2013 Citroen C4 L,2013 Citroen C4 Aircross,2013 Citroen C3 Picasso,2013 Citroen C1,2013 Citroen C-Elysee,2012 Citroen Numero 9 Concept,2012 Citroen DS5,2012 Citroen DS4 Racing Concept,2012 Citroen DS4,2011 Citroen Tubik Concept,2011 Citroen DS3 Racing,2011 Citroen DS3 R3,2011 Citroen DS3,2011 Citroen C5,2011 Citroen C4,2011 Citroen C-Zero,2010 Citroen Survolt Concept,2010 Citroen Metropolis Concept,2010 Citroen Lacoste Concept,2010 Citroen GQ Concept,2010 Citroen DS High Rider Concept,2010 Citroen C3,2009 Citroen REVOLTe Concept,2009 Citroen DS Inside Concept,2009 Citroen C4 Coupe,2009 Citroen C4,2009 Citroen C3 Pluriel Charleston,2009 Citroen C3 Picasso,2009 Citroen C2,2009 Citroen C1,2009 Citroen Berlingo Multispace,2008 Citroen Hypnos Concept,2008 Citroen GT Concept,2008 Citroen C5 Estate,2008 Citroen C5,2008 Citroen C4 notchback,2008 Citroen C4 WRC HYmotion4 Concept,2008 Citroen C4 Sedan,2007 Citroen Grand C4 Picasso,2007 Citroen Cruise Crosser Concept,2007 Citroen C5 Airscape Concept,2007 Citroen C4 Picasso,2007 Citroen C-Crosser,2007 Citroen C-Cactus Concept,2006 Citroen C6,2006 Citroen C3 X-TR,2006 Citroen C3 VTR,2006 Citroen C3 Pluriel,2006 Citroen C3,2006 Citroen C1 5door,2006 Citroen C1 3door,2006 Citroen C-Metisse Concept,2006 Citroen C-Buggy Concept,2005 Citroen C5 Break,2005 Citroen C5,2005 Citroen C4 Coupe with Panoramic Sunroof,2005 Citroen C4 Coupe Enterprise,2005 Citroen C4 Coupe,2005 Citroen C4,2005 Citroen C-SportLounge Concept Car,2005 Citroen C-Airplay Concept,2004 Citroen Xsara Picasso,2004 Citroen C4 Sport Concept,2004 Citroen C3 Pluriel HDi 70,2004 Citroen C2,2003 Citroen CAirlounge Concept,2003 Citroen C8 Exclusive,2002 Citroen C-Airdream Concept,2001 Citroen Xsara Picasso,2001 Citroen C-Crosser Concept
Note:
1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Citroen makes.
2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.
3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.
4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.
5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.