Description
OBD-II Trouble Code Description for P0108 Citroen
Manifold Absolute Pressure/Barometric Pressure Circuit High Input
What does this mean?
OBD2 Code P0108 Citroen definition:
The MAP (Manifold Absolute Pressure) sensor measures engine manifold negative air pressure. It’s usually a three wire sensor: a ground wire, a 5 volt reference wire from the PCM (Powertrain Control Module) to the MAP sensor, and a signal wire that informs the PCM of the MAP sensor voltage reading as it changes. The higher the engine vacuum, the lower the voltage reading. The voltage should range between about 1 volt (at idle) to about 5 volts (WOT wide open throttle). If the PCM sees the voltage reading from the MAP sensor is greater than 5 Volts, or if the voltage reading is higher than what the PCM considers normal under certain circumstances, a P0108 Citroen DTC will set.
Symptoms
Possible sumptoms of OBD code P0108 Citroen
MIL (Malfunction Indicator Lamp) will likely be on Engine may run poorly Engine may not run at all Fuel mileage may decrease Presence of black smoke at exhaust
Causes
Possible causes of OBD code P0108 Citroen
Bad MAP sensor Leak in vacuum supply line to MAP sensor Engine vacuum leak Short on signal wire to PCM Short on reference voltage wire from PCM Open in ground circuit to MAP Worn engine causing low vacuum
Possible Solutions
A good way to diagnose if the MAP sensor is to blame would be to compare the KOEO (key on engine off) MAP sensor reading on a scan tool with the Barometric pressure reading. They should be the same because they both measure atmospheric pressure. If the MAP reading is greater than 0.5 volt off of the BARO reading, then replacing the MAP sensor would likely fix the problem. Otherwise, start the engine and observe the MAP reading at idle. It should normally be about 1.5 volts (varies according to altitude). a. If it is, the problem is likely intermittent. Check all the vacuum hoses for damage and replace as necessary. You can also try wiggle testing the harness and connector to reproduce the problem. b. If the scan tool MAP reading is more than 4.5 volts, check the actual engine vacuum reading with the engine running. If it is less than 15 or 16 in. Hg, then the PCM is probably not seeing enough vacuum (due to a worn engine, perhaps) for a given operating condition (which causes a higher than normal voltage signal to the PCM) and setting the code. Repair the engine vacuum problem and retest. c. But, if the actual engine vacuum reading is 16 in. Hg or more, then unplug the MAP sensor. The scan tool MAP reading should indicate that there is no voltage present. Check that the ground from the PCM is intact and also that the MAP sensor connector and terminals are tight. If the connection is good, then replace the map sensor. d. However if, with KOEO, & the MAP sensor unplugged, the scan tool shows a voltage reading, then there may be a short in the harness to the MAP sensor. Turn the ignition off. At the PCM unplug connector and remove the MAP signal wire from the connector. Re-attach the PCM connector and see if with KOEO, the scan tool MAP reading shows voltage. If it still does, replace the PCM. If not, check for voltage on the signal wire you just removed from the PCM. If there is voltage on the signal wire, find the short in the harness and repair.
The OBD2 Code Information Be Applicable For Citroen :
2013 Citroen Technospace Concept,2013 Citroen DS Wild Rubis Concept,2013 Citroen DS3 Cabrio Racing Concept,2013 Citroen Cactus Concept,2013 Citroen C4 L,2013 Citroen C4 Aircross,2013 Citroen C3 Picasso,2013 Citroen C1,2013 Citroen C-Elysee,2012 Citroen Numero 9 Concept,2012 Citroen DS5,2012 Citroen DS4 Racing Concept,2012 Citroen DS4,2011 Citroen Tubik Concept,2011 Citroen DS3 Racing,2011 Citroen DS3 R3,2011 Citroen DS3,2011 Citroen C5,2011 Citroen C4,2011 Citroen C-Zero,2010 Citroen Survolt Concept,2010 Citroen Metropolis Concept,2010 Citroen Lacoste Concept,2010 Citroen GQ Concept,2010 Citroen DS High Rider Concept,2010 Citroen C3,2009 Citroen REVOLTe Concept,2009 Citroen DS Inside Concept,2009 Citroen C4 Coupe,2009 Citroen C4,2009 Citroen C3 Pluriel Charleston,2009 Citroen C3 Picasso,2009 Citroen C2,2009 Citroen C1,2009 Citroen Berlingo Multispace,2008 Citroen Hypnos Concept,2008 Citroen GT Concept,2008 Citroen C5 Estate,2008 Citroen C5,2008 Citroen C4 notchback,2008 Citroen C4 WRC HYmotion4 Concept,2008 Citroen C4 Sedan,2007 Citroen Grand C4 Picasso,2007 Citroen Cruise Crosser Concept,2007 Citroen C5 Airscape Concept,2007 Citroen C4 Picasso,2007 Citroen C-Crosser,2007 Citroen C-Cactus Concept,2006 Citroen C6,2006 Citroen C3 X-TR,2006 Citroen C3 VTR,2006 Citroen C3 Pluriel,2006 Citroen C3,2006 Citroen C1 5door,2006 Citroen C1 3door,2006 Citroen C-Metisse Concept,2006 Citroen C-Buggy Concept,2005 Citroen C5 Break,2005 Citroen C5,2005 Citroen C4 Coupe with Panoramic Sunroof,2005 Citroen C4 Coupe Enterprise,2005 Citroen C4 Coupe,2005 Citroen C4,2005 Citroen C-SportLounge Concept Car,2005 Citroen C-Airplay Concept,2004 Citroen Xsara Picasso,2004 Citroen C4 Sport Concept,2004 Citroen C3 Pluriel HDi 70,2004 Citroen C2,2003 Citroen CAirlounge Concept,2003 Citroen C8 Exclusive,2002 Citroen C-Airdream Concept,2001 Citroen Xsara Picasso,2001 Citroen C-Crosser Concept
Note:
1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Citroen makes.
2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.
3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.
4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.
5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.