Description
OBD-II Trouble Code Description for P0326 Citroen
Knock Sensor 1 Circuit Range/Performance
What does this mean?
OBD2 Code P0326 Citroen definition:
Knock sensors are used to detect engine pre-detonation (engine knock or ping). The knock sensor (KS) is usually a two wire sensor. A 5 volt reference is supplied to the sensor and there is a signal return from the knock sensor to the PCM (powertrain control module). The sensor signal wire informs the PCM when a knock occurs and in what degree of severity. The PCM will retard the spark timing to avoid pre-detonation. Most PCMs have the ability to learn spark knock trends in the engine during normal operation. If the PCM determines that the knock is out of the ordinary or that the noise level is abnormally high, P0326 Citroen may set. If the PCM senses that the knock is severe and cannot be eliminated by retarding the spark timing, P0326 Citroen may set. Keep in mind that knock sensors cannot distinguish between a knock from pre-detonation or one from engine problems.
Symptoms
Possible sumptoms of OBD code P0326 Citroen
Symptoms of a P0326 Citroen DTC may include: MIL (Malfunction Indicator Lamp) illumination Audible knocking from the engine compartment Pinging from engine under acceleration
Causes
Possible causes of OBD code P0326 Citroen
Potential causes of a P0326 Citroen code include: Knock sensor connector is damaged Knock sensor circuit is open or shorted to ground Knock sensor circuit is shorted to voltage Knock sensor has failed Moisture in knock sensor connectors Incorrect fuel octane PCM has failed
Possible Solutions
If an engine knock can be heard, fix the source of the mechanical problem first then retest. Make sure the proper octane of fuel was used in the engine. Using lower octane fuel than what is specified can cause a ping or pre-detonation and may cause P0326 Citroen. Unplug the knock sensor and check for water or corrosion in the connector. If the knock sensor has a seal, verify there is no coolant from the engine block fouling the sensor. Repair as necessary. Turn ignition to run position with engine off. Ensure that 5 Volts are present at the KS connector. If there is, check for proper resistance between KS terminal and engine ground. You will need a vehicle specification for this. If resistance is out of specification, replace the knock sensor. If resistance is normal, plug KS back in and idle the engine. Using a scan tool in datastream, observe KS value. Does it indicate a knock is present at idle? If so, replace the knock sensor. If the knock sensor shows no knock at idle, then tap on the engine block while observing the knock signal. If it doesn’t show a signal that corresponds with the taps, replace the knock sensor. If it does, verify the knock sensor wiring isn’t routed next to ignition wires. If there was no 5 volts present at the knock sensor connector while unplugged with KOEO (Key on engine off) then go back to the PCM connector. Turn ignition off and clip the knock sensor 5 volt reference wire in a location that is easy to repair (Or remove the wire from the PCM connector). With KOEO, check for 5 volts on the PCM side of the clipped wire. If 5 volts isn’t present, suspect a bad PCM. If 5 volts IS present, repair short in 5 volt reference circuit. Since the reference circuit is a shared circuit, you will need to check all engine sensors that are fed a 5 volt reference. Unplug each sensor one at a time until the reference voltage returns. When it returns the last sensor you plugged in is the shorted sensor. If no sensors are shorted, check the wiring harness for short to voltage on reference circuit.
The OBD2 Code Information Be Applicable For Citroen :
2013 Citroen Technospace Concept,2013 Citroen DS Wild Rubis Concept,2013 Citroen DS3 Cabrio Racing Concept,2013 Citroen Cactus Concept,2013 Citroen C4 L,2013 Citroen C4 Aircross,2013 Citroen C3 Picasso,2013 Citroen C1,2013 Citroen C-Elysee,2012 Citroen Numero 9 Concept,2012 Citroen DS5,2012 Citroen DS4 Racing Concept,2012 Citroen DS4,2011 Citroen Tubik Concept,2011 Citroen DS3 Racing,2011 Citroen DS3 R3,2011 Citroen DS3,2011 Citroen C5,2011 Citroen C4,2011 Citroen C-Zero,2010 Citroen Survolt Concept,2010 Citroen Metropolis Concept,2010 Citroen Lacoste Concept,2010 Citroen GQ Concept,2010 Citroen DS High Rider Concept,2010 Citroen C3,2009 Citroen REVOLTe Concept,2009 Citroen DS Inside Concept,2009 Citroen C4 Coupe,2009 Citroen C4,2009 Citroen C3 Pluriel Charleston,2009 Citroen C3 Picasso,2009 Citroen C2,2009 Citroen C1,2009 Citroen Berlingo Multispace,2008 Citroen Hypnos Concept,2008 Citroen GT Concept,2008 Citroen C5 Estate,2008 Citroen C5,2008 Citroen C4 notchback,2008 Citroen C4 WRC HYmotion4 Concept,2008 Citroen C4 Sedan,2007 Citroen Grand C4 Picasso,2007 Citroen Cruise Crosser Concept,2007 Citroen C5 Airscape Concept,2007 Citroen C4 Picasso,2007 Citroen C-Crosser,2007 Citroen C-Cactus Concept,2006 Citroen C6,2006 Citroen C3 X-TR,2006 Citroen C3 VTR,2006 Citroen C3 Pluriel,2006 Citroen C3,2006 Citroen C1 5door,2006 Citroen C1 3door,2006 Citroen C-Metisse Concept,2006 Citroen C-Buggy Concept,2005 Citroen C5 Break,2005 Citroen C5,2005 Citroen C4 Coupe with Panoramic Sunroof,2005 Citroen C4 Coupe Enterprise,2005 Citroen C4 Coupe,2005 Citroen C4,2005 Citroen C-SportLounge Concept Car,2005 Citroen C-Airplay Concept,2004 Citroen Xsara Picasso,2004 Citroen C4 Sport Concept,2004 Citroen C3 Pluriel HDi 70,2004 Citroen C2,2003 Citroen CAirlounge Concept,2003 Citroen C8 Exclusive,2002 Citroen C-Airdream Concept,2001 Citroen Xsara Picasso,2001 Citroen C-Crosser Concept
Note:
1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Citroen makes.
2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.
3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.
4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.
5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.