Ford P0120 Throttle Pedal Position Sensor/Switch A Circuit Malfunction

Description

OBD-II Trouble Code Description for P0120 Ford

Throttle/Pedal Position Sensor/Switch “A” Circuit

What does this mean?

OBD2 Code P0120 Ford definition:
The TPS (Throttle Position Sensor) is a potentiometer that is mounted to the throttle body. It detects the throttle blade angle. As the throttle blade moves, the TPS sends a signal to the PCM (Powertrain Control Module). Usually a three wire sensor: A 5 volt reference from the PCM to the TPS, a ground from the PCM to the TPS, and a signal return from the TPS to the PCM.

The TPS sends the throttle position information back to the PCM on this signal wire. When the throttle is closed the signal is near .45 volts. At WOT (Wide Open Throttle) the TPS signal voltage will approach a full 5 volts. When the PCM sees a voltage that is outside of normal operating range, P0120 Ford will set.

NOTE: The PCM knows that any large change in throttle position means a cooresponding change in manifold pressure (MAP). On some models the PCM will monitor MAP and TPS operation for comparison. Meaning that if the PCM sees a large percentage change in throttle position, it expects to see a cooresponding change in manifold pressure and vice versa. If it doesn’t see this comparitive change, P0120 Ford may set. This doesn’t apply to all models.

Symptoms

Possible sumptoms of OBD code P0120 Ford
Potential symptoms include:

MIL (Malfunction Indicator Lamp) illumination
Misfiring at idle or at highway speed
Poor idle quality
Possibly won’t idle
Possibly starts and stalls

Causes

Possible causes of OBD code P0120 Ford
Potential causes of the P0120 Ford code include:

Sticking throttle return spring
MAP or TPS connector corrosion
Misrouted harness causing chafing
Bad TPS
Bad PCM

Possible Solutions

If you have access to a scan tool, with KOEO (Key on engine off) observe the TPS voltage. With throttle closed, voltage should be about .45 volts. It should gradually sweep upwards to approximately 4.5 to 5 volts as you depress the throttle. Sometimes only a scope can capture an intermittent glitch in the TPS signal voltage. If you notice a glitch in the TPS sweep voltage, replace the TPS.

NOTE: Some TPS sensors require fine adjustment. If you aren’t comfortable with using a DVOM (Digital Volt Ohm meter) to adjust the new TPS, then it’s best to take the vehicle to a shop. If the voltage is not .45 volts (+or- .3 volts or so) with the throttle closed or if the reading is “stuck” then unplug the TPS connector. With KOEO check for 5 volts reference voltage present at the connector and a good ground. You can check the signal circuit for continuity by jumping a fused wire between the ground circuit of the TPS connector and the signal circuit. If the TPS reading on the scan tool now reads zero, then replace the TPS. However if that doesn’t change the reading to zero, then check for an open or a short on the signal wire and if none is found, suspect a bad PCM. If manipulating the TPS wiring harness causes any change in idle, then suspect bad TPS.

Related Codes

P0121 Ford P0122 Ford P0123 Ford P0124 Ford


The OBD2 Code Information Be Applicable For Ford:

2013 Ford Taurus,2013 Ford Mustang,2013 Ford Kuga,2013 Ford Fusion,2012 Ford Focus,2011 Ford Mondeo,2011 Ford Focus,2011 Ford Edge,2010 Ford Mustang,2009 Ford Focus,2008 Ford Fiesta,2008 Ford Escape,2007 Ford Mondeo,2006 Ford Focus,2005 Ford Mustang,2005 Ford Escape,2003 Ford Mustang,2003 Ford Focus,2000 Ford Mustang

 

Note:

1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Ford makes.

2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.

3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.

4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.

5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.