Description
OBD-II Trouble Code Description for P1000 Ford
OBD-II Monitor Testing Incomplete
Ford P1000 OBD system readiness test not complete
OBD-II Trouble Code Description for P1000 Ford
OBD system readiness test not complete
What does this mean?
OBD2 Code P1000 Ford definition:
The OBD monitors are performed during the OBD Drive Mode. The P1000 Ford will be stored in continuous memory if any of the OBD monitors do not complete their full diagnostic check.
Causes
Possible causes of OBD code P1000 Ford
? Vehicle is new from the factory ? Battery or PCM had recently been disconnected ? An OBD monitor failure had occurred before completion of an OBD drive mode ? The PCM DTCs have recently been cleared with a M-MDS ? The PCM has been flashed and the vehicle has not yet completed an OBD drive mode.
Possible Solutions
Diagnostic procedure
|
STEP |
INSPECTI FordON |
ACTION Ford |
|
|---|---|---|---|
|
1
|
VERIFY FREEZE FRAME DATA HAS BEEN RECORDE FordD
???Has the FREEZE FRAME DATA been recorded?
|
Yes
|
Go to the next step.
|
|
No
|
Record the FREEZE FRAME DATA on the repair order, then go to the next step.
|
||
|
2
|
VERIFY REPAIR INFORMATION AVAILABILIT FordY
???Verify related service repair information availability.
???Is any related repair information available?
|
Yes
|
Perform repair or diagnosis according to the available repair information.
If the vehicle is not repaired, go to the next step.
|
|
No
|
Go to the next step.
|
||
|
3
|
CHECK Ford FOR ANY OTHER DTCS
???Where any other DTCs received with the P1000 Ford?
|
Yes
|
Go to the applicable DTC inspection.
|
|
No
|
Go to the next step.
|
||
|
4
|
REQUEST TO CLEAR Ford DTC P1000 Ford
???Has the customer requested the DTC P1000 Ford be cleared?
|
Yes
|
Complete an OBD drive mode, then go to the next step.
|
|
No
|
Inform the customer that if the law in your area required additional driving in order to clear the DTC P1000 Ford from the PCM memory, it must be complete before an inspection/maintenance test.
|
||
|
5
|
VERIFY THAT DTC P1000 Ford TROUBLES FordHOOTING IS COMPL FordETED
???Make sure to reconnect all disconnected connectors.
???Clear the DTC from the PCM memory using the M-MDS.
???Start the engine and warm-up to normal operating temperature.
???Run the vehicle under the FREEZE FRAME DATA stored condition.
???Retrieve the DTC using the M-MDS.
???Is the PENDI FordNG CODE same DTC present?
|
Yes
|
Replace PCM, then go to the next step.
|
|
No
|
Go to the next step.
|
||
|
6
|
VERIFY AFTER REPAIR PROCE FordDURE
???Perform “After Repair Procedure”.
???Is there any DTC present?
|
Yes
|
Go to the applicable DTC inspection.
|
|
No
|
Troubleshooting completed.
|
||
Mercedes OBD-II Trouble Code Description for P1000 Ford
Electronic Gear Selector Module: Defective N15/5
The OBD2 Code Information Be Applicable For Ford:
2013 Ford Taurus,2013 Ford Mustang,2013 Ford Kuga,2013 Ford Fusion,2012 Ford Focus,2011 Ford Mondeo,2011 Ford Focus,2011 Ford Edge,2010 Ford Mustang,2009 Ford Focus,2008 Ford Fiesta,2008 Ford Escape,2007 Ford Mondeo,2006 Ford Focus,2005 Ford Mustang,2005 Ford Escape,2003 Ford Mustang,2003 Ford Focus,2000 Ford Mustang
Note:
1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Ford makes.
2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.
3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.
4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.
5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.