GMC P0156 HO2S22 Sensor Range/Performance Condition

Description

OBD-II Trouble Code Description for P0156 GMC

O2 Sensor Circuit

What does this mean?

OBD2 Code P0156 GM definition:
The o2 (oxygen) sensors measure oxygen content in the exhaust. The PCM (powertrain control module) then uses this information to regulate fuel injector pulse. The o2 sensors are very important for the proper operation of the engine. Innacurate or faulty o2 sensors can cause the PCM to add or take away fuel based on the faulty o2 sensor voltage which can cause a host of problems. A P0156 GM code definition:the Bank 2,2 o2 sensor or the downstream (post-cat) o2 sensor on Bank 2. It is a four wire sensor. The PCM supplies a ground circuit and a reference voltage circuit of about 0.5 volts. Also for the o2 sensor heater element there is a battery voltage supply wire and another ground circuit for that. The o2 sensor heater allows the o2 sensor to warm up faster, thus achieving closed loop in less time than it would normally take for the exhaust to warm the sensor up to operating temperature. The O2 sensor varies the supplied reference voltage based on oxygen content in the exhaust. It is capable of varying from about 0.1 to 0.9 volts, 0.1 V indicating lean exhaust and 0.9 V indicating rich exhaust. This P0156 GM code indicates that the Bank 2, 2 o2 sensor is stuck low for too long or isn’t active at all.

Symptoms

Possible sumptoms of OBD code P0156 GM
Often post-cat o2 sensor problems present few symptoms since they are inputs to the PCM to monitor catalytic converter quality and don’t directly control fuel. sometimes no symptoms are noticeable. However the following may be possible on some vehicles: MIL (Malfunction Indicator Lamp) illumination Decrease in MPG Increase in tailpipe emissions

Causes

Possible causes of OBD code P0156 GM
Potential causes of an P0156 GM code include: Bad O2 sensor Signal shorted to voltage Wiring problems due to contact with exhaust components Holes in exhaust near o2 sensor

Possible Solutions

If you have access to a scan tool, check the signal voltage for the Bank 2,2 oxygen sensor with the engine at normal operating temperature. Is it stuck low currently? If so, increase RPM for a few seconds and see if it affects the reading. If it begins working with increased RPM, check for holes in the exhaust near the o2 sensor that may cause a false lean. If the exhaust pipe is intact, the sensor is sluggish, replace it. If the Bank 2,2 o2 sensor voltage reading remains low with increased RPM, unplug it and then observe the reading. It should have increased to about 0.5 volts or thereabouts. If it did, check for water intrusion or other connector problems. If none are found, replace the shorted o2 sensor. If the voltage reading is still stuck low after unplugging the sensor, then suspect a wiring problem. Using a voltmeter, with the o2 sensor unplugged, check for voltage on the signal circuit at the o2 sensor connector(PCM side). It can vary with model, but should be about 0.5 volts and not above 1 volt. If the voltage reading is too high, repair short to voltage on signal circuit. If the signal voltage checks out, suspect the PCM.


The OBD2 Code Information Be Applicable For GMC:

2013 GMC Terrain Denali,2013 GMC Acadia,2011 GMC Sierra All Terrain HD Concept,2010 GMC Terrain,2010 GMC Granite Concept,2009 GMC Sierra Hybrid Crew Cab,2008 GMC Yukon Hybrid,2008 GMC Denali XT Concept,2007 GMC Yukon XL,2007 GMC Yukon Denali,2007 GMC Yukon,2007 GMC Sierra Denali,2007 GMC Sierra Classic,2007 GMC Sierra 3500 HD SLT Crew Cab,2007 GMC Sierra 2500 HD SLT Extended Cab,2007 GMC Sierra,2007 GMC Acadia,2005 GMC Sierra Denali 1500 Crew Cab,2005 GMC Graphyte Concept,2005 GMC Envoy XL Denali,2005 GMC Envoy Denali

Note:

1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the GMC makes.
2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.
3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.
4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.

5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.