Description
OBD-II Trouble Code Description for P0211 Honda
Injector Circuit/Open – Cylinder 11
What does this mean?
OBD2 Code P0211 Honda definition:
P0210 Honda means that the PCM detected a fault in the injector or the wiring to the injector. It monitors the injector and when the injector is activated, the PCM expects to see the voltage pulled “low” or close to zero. When the injector is switched off, the PCM expects to see a voltage that is close to battery voltage or “high”. If it doesn’t see the expected voltage the PCM will set this code. The PCM also monitors resitance in the circuit. If the resistance is excessively low or high it will set this code.
Symptoms
Possible sumptoms of OBD code P0211 Honda
The symptoms for this code will likely be a misfire and a rough running engine. Poor acceleration. The MIL will also be illuminated.
Causes
Possible causes of OBD code P0211 Honda
The causes of a P0210 Honda engine light code could be any of the following: Bad injector. This is usually the cause of this code but doesn’t rule out the possibility of one of the other causes Open in the wiring to the injector Short in the wiring to the injector Bad PCM
Possible Solutions
First, using a DVOM check the resistance of the injector. If it isn’t within specs, then replace the injector. Check for voltage at the fuel injector connector. It should have 10 volts or more. Visually check the connector for damage or broken wires. Visually check the injector for damage. If you have access to an injector tester, activate the injector and see if it operates. If the injector operates, then you likely have either an open in the wiring, or a blocked injector. If you do not have access to a tester, swap the injector with another one and see if the code changes. If the code changes, then change the injector. At the PCM, remove the driver wire from the PCM connector and Ground the wire. (Make sure you have the correct wire. If you’re not sure, do not attempt) The injector should activate Replace the injector First, using a DVOM check the resistance of the injector. If it isn’t within specs, then replace the injector. Check for voltage at the fuel injector connector. It should have 10 volts or more. Visually check the connector for damage or broken wires. Visually check the injector for damage. If you have access to an injector tester, activate the injector and see if it operates. If the injector operates, then you likely have either an open in the wiring, or a blocked injector. If you do not have access to a tester, swap the injector with another one and see if the code changes. If the code changes, then change the injector. At the PCM, remove the driver wire from the PCM connector and Ground the wire. (Make sure you have the correct wire. If you’re not sure, do not attempt) The injector should activate Replace the injector
The OBD2 Code Information Be Applicable For Honda:
2013 Honda Urban SUV Concept,2013 Honda S660 Concept new,2013 Honda NSX-GT Concept,2013 Honda N-One,2013 Honda GEAR Concept,2013 Honda Civic,2013 Honda CR-Z,2012 Honda Civic,2011 Honda Jazz,2011 Honda Accord,2010 Honda Insight,2010 Honda CR-V,2009 Honda City,2008 Honda S2000,2008 Honda Accord,2007 Honda Fit,2007 Honda Civic,2007 Honda CR-V,2007 Honda Accord,2006 Honda Civic,2005 Honda Element,2005 Honda CRV SE,2005 Honda CRV EX,2003 Honda Element,2003 Honda CR-V,2002 Honda NSX,2002 Honda Civic Si,2002 Honda Accord SE,2001 Honda NSXR Concept,2001 Honda Model X Concept,2001 Honda Civic Si Concept,2001 Honda Civic Concept,2001 Honda CR-V,2001 Honda Accord Sedan,2001 Honda Accord Coupe,2000 Honda S2000,2000 Honda Passport,2000 Honda Insight
Note:
1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Honda makes.
2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.
3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.
4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.
5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.