Honda P0216 Injection Timing Control Circuit Malfunction

Description

OBD-II Trouble Code Description for P0216 Honda

Injector/Injection Timing Control Circuit

What does this mean?

OBD2 Code P0216 Honda definition:
Basically this means the diesel fuel injection pump has a timing failure. This could be that the injection pump timing needs adjusted OR the failure is internal to the injection pump and therefore non-adjustable. NOTE: If your vehicle is a Dodge Ram with Cummins engine then be aware that fuel delivery problems frequently cause this code. Prolonged fuel delivery problems can cause injection pump failure!

Symptoms

Possible sumptoms of OBD code P0216 Honda
Symptoms of a P0216 Honda DTC may include: P0216 Honda DTC Low power Crank, but no start Hard start Displays an intermittent stumble or miss Engine may start and then stall Engine may appear to drive fine but surge at idle

Causes

Possible causes of OBD code P0216 Honda
The most frequent cause of this code is a bad injection pump due to poor fuel delivery. Fuel delivery problems could be: A plugged diesel fuel filter An in-tank blockage Air in the fuel due to a cracked in-tank fuel ine above the fuel level Bad transfer (lift) pump Injection pump out of time

Possible Solutions

First, simply check if your injection pump timing is adjustable. If so, check the timing and adjust if necessary. If you think that you may have a fuel delivery problem, then check the lift pump operation. On Dodge Ram with the Cummins engine, the lift pump should produce about 45 oz of diesel in 25 seconds of operation. This can be performed by disconnecting the fuel hose from the injection pump and pumping the fuel into an approved container. Bump the engine over but do not start it. Then the lift pump will operate for 25 seconds. If the fuel is aerated, then check/repair fuel line and recheck. With the fuel hose connected the fuel pressure should be 10psi. If the fuel delivery tests fail, replace the diesel fuel filter and recheck. If it still fails then verify there are no restrictions in the fuel tank Then replace the lift (transfer) pump. IT SHOULD BE NOTED that if this code surfaced after a routine fuel filter replacement or if you have any of the above symptoms after routine fuel filter replacement, then suspect the fuel transfer pump. This occurs because even a weak transfer pump can still provide enough fuel for the engine to run. But when the fuel system’s prime is lost due to fuel filter replacement, it may not restart again without fixing the fuel delivery problem. If you found your injection pump to be bad, the lift pump should be checked for operation to protect the new injection pump. This is because weak or low output from lift pump are common cause of injection pump failure. There are some aftermarket kits that can be purchased to warn the operator when the fuel pressure/volume drops to level that could damage the injection pump.


The OBD2 Code Information Be Applicable For Honda:

2013 Honda Urban SUV Concept,2013 Honda S660 Concept new,2013 Honda NSX-GT Concept,2013 Honda N-One,2013 Honda GEAR Concept,2013 Honda Civic,2013 Honda CR-Z,2012 Honda Civic,2011 Honda Jazz,2011 Honda Accord,2010 Honda Insight,2010 Honda CR-V,2009 Honda City,2008 Honda S2000,2008 Honda Accord,2007 Honda Fit,2007 Honda Civic,2007 Honda CR-V,2007 Honda Accord,2006 Honda Civic,2005 Honda Element,2005 Honda CRV SE,2005 Honda CRV EX,2003 Honda Element,2003 Honda CR-V,2002 Honda NSX,2002 Honda Civic Si,2002 Honda Accord SE,2001 Honda NSXR Concept,2001 Honda Model X Concept,2001 Honda Civic Si Concept,2001 Honda Civic Concept,2001 Honda CR-V,2001 Honda Accord Sedan,2001 Honda Accord Coupe,2000 Honda S2000,2000 Honda Passport,2000 Honda Insight

 

Note:

1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Honda makes.

2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.

3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.

4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.

5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.