Hummer P0051 HO2S Heater Control Circuit Low Bank 2 Sensor 1

Description

OBD-II Trouble Code Description for P0051 Hummer

HO2S Heater Control Circuit Low

What does this mean?

OBD2 Code P0051 Hummer definition:
A P0051 Hummer DTC (diagnostic trouble code) definition:the O2 sensor (oxygen sensor) located on Bank 2 in front of the catalytic converter. There is also an oxygen sensor behind the converter which is Sensor #2. This O2 sensor #1 may also be refered to as an air/fuel ratio sensor since on some vehicles it is. It detects the amount of oxygen in the exhaust gas compared to the outside air and then vehicle’s computer adjusts the air/fuel ratio going into the engine. The sensor is less effective when the exhaust gas temperature is low, so it includes a heater which is activated to help get better readings from the A/F O2 sensor. Essentially this P0051 Hummer code means that the resistance of the heater circuit is lower than normal. In most cases, that resistance level must fall below 0.8 A to trigger the DTC code. Note, this code is very similar in nature to P0031 Hummer, P0032 Hummer, and P0052 Hummer

Symptoms

Possible sumptoms of OBD code P0051 Hummer
Most likely you’ll not notice any symptoms other than the MIL (malfunction indicator lamp, a.k.a. the check engine light) will illuminate.

Causes

Possible causes of OBD code P0051 Hummer
A P0051 Hummer DTC trouble code may be caused by one or more of the following: A short in the heater circuit in the sensor A failed O2 sensor heater Wiring/connectors broken/frayed leading to sensor and/or relay Failed PCM/ECM

Possible Solutions

To fix a P0051 Hummer DTC code, you’ll need to do a proper diagnosis. To do that, you’ll want to inspect the wiring and connectors leading to the sensor. Also if equipped with a heater relay and fuse, you’ll want to check those as well. Use a digital volt ohm meter to: check for 12 volts at the heater circuit feed (hint: unplug the sensor and check at the wiring connector to do this measurement) check the ground circuit for continuity measure the resistance of the heater circuit (done on the sensor itself) measure the resistance and voltage of the wiring Refer to a service manual for the correct specifications (volts, ohms) for your vehicle. On some Toyota vehicles this code is triggered when the resistance of the heater circuit is below 0.8 A. With that said, a common fix for this DTC is to replace the air/fuel (O2 oxygen) sensor #1 on bank 2 (the side of the engine that doesn’t contain cylinder #1). Please keep in mind that OEM (original equipment) replacement sensors are recommended (from the dealer). Aftermarket sensors can be less reliable and of poorer quality (not always, but more often). There’s also a chance that replacement parts for the P0051 Hummer code may also fall under a federal emissions warranty (check with your dealer to see if it’s covered).


The OBD2 Code Information Be Applicable For Hummer:

2009 Hummer H3T Alpha,2008 Hummer HX Concept,2008 Hummer H3 Wagon Concept,2008 Hummer H3 Alpha,2008 Hummer H2,2007 Hummer H3 Open Top,2007 Hummer H3X,2007 Hummer H3R Off Road Concept,2007 Hummer H2 Safari Concept,2006 Hummer H3,2006 Hummer H2 SUT Limited Edition,2006 Hummer H1 Alpha,2005 Hummer H3 Street,2005 Hummer H2 SUT,2004 Hummer H2 SUT Concept,2004 Hummer H2H Hydrogen Concept,2004 Hummer H2,2004 Hummer H1,2003 Hummer Humvee Military Vehicle,2003 Hummer H3T Concept,2003 Hummer H2 with GM Accessories,2003 Hummer H2 SUV,2003 Hummer H2 SUT Dirt Sport Concept,2003 Hummer H1,2003 Hummer Bike,2002 Hummer H2 SUV Concept,2002 Hummer H1 10th Anniversary Edition,2002 Hummer H1,2001 Hummer H1 Alpha Concept

 

Note:

1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Acura makes.

2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.

3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.

4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.

5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.