Description
OBD-II Trouble Code Description for P0341 Hummer
Camshaft Position Sensor “A” Circuit Range/Performance
What does this mean?
OBD2 Code P0341 Hummer definition:
This P0341 Hummer code basically means that the powertrain control module (PCM) detected a problem with the camshaft signal. The camshaft position sensor (CPS) sends a specific signal to the PCM for Top Dead Center on the compression stroke as well as signals indicating the position of the cam sensor. This is accomplished through a reluctor wheel attached to the camshaft that passes by the cam sensor. Any time that the signal to the PCM is inconsistent with what the signal should be, this code is set. NOTE: this code can also be set by extended cranking periods.
Symptoms
Possible sumptoms of OBD code P0341 Hummer
The car will likely run with this code set, as it is often intermittent and also because the PCM can often operate the vehicle in “limp-in/limp-home” mode even with a cam sensor signal problem. There may be no noticeable symptoms other than: Poor fuel economy (if engine runs) Possible no start condition
Causes
Possible causes of OBD code P0341 Hummer
A code P0341 Hummer may mean that one or more of the following has happened: Cam sensor wiring routed too close to spark plug wiring (causing interference) Poor wiring connection at cam sensor Poor wiring connection at PCM Bad cam sensor Damaged reluctor wheel
Possible Solutions
Often relacing the sensor fixes this code, but not necessarily. Therefore it’s important to check the following: Check that the wiring isn’t routed too close to any secondary ignition components (coil, spark plug wires, etc.) Visually inspect the wiring at the sensor for any burn marks, discoloration indicative of melting or chafing Visually inspect the cam sensor for damage Visually inspect the reluctor wheel through the cam sensor port (if possible) for any missing teeth or any damage If reluctor isn’t visible from outside the engine, visual test can only be done by removing cam shaft or intake manifold (depending on engine design) If all checks out okay, then replace the sensor. Related Camshaft Trouble Codes: P0340 Hummer
The OBD2 Code Information Be Applicable For Hummer:
2009 Hummer H3T Alpha,2008 Hummer HX Concept,2008 Hummer H3 Wagon Concept,2008 Hummer H3 Alpha,2008 Hummer H2,2007 Hummer H3 Open Top,2007 Hummer H3X,2007 Hummer H3R Off Road Concept,2007 Hummer H2 Safari Concept,2006 Hummer H3,2006 Hummer H2 SUT Limited Edition,2006 Hummer H1 Alpha,2005 Hummer H3 Street,2005 Hummer H2 SUT,2004 Hummer H2 SUT Concept,2004 Hummer H2H Hydrogen Concept,2004 Hummer H2,2004 Hummer H1,2003 Hummer Humvee Military Vehicle,2003 Hummer H3T Concept,2003 Hummer H2 with GM Accessories,2003 Hummer H2 SUV,2003 Hummer H2 SUT Dirt Sport Concept,2003 Hummer H1,2003 Hummer Bike,2002 Hummer H2 SUV Concept,2002 Hummer H1 10th Anniversary Edition,2002 Hummer H1,2001 Hummer H1 Alpha Concept
Note:
1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Acura makes.
2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.
3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.
4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.
5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.