Hyundai P0031 HO2S Heater Control Circuit Low Bank 1 Sensor 1

Description

OBD-II Trouble Code Description for P0031 Hyundai

HO2S Heater Control Circuit Low

What does this mean?

OBD2 Code P0031 Hyundai definition:
A P0031 Hyundai DTC (diagnostic trouble code) definition:the O2 sensor (oxygen sensor) located on Bank 1 in front of the catalytic converter. There is also an oxygen sensor behind the converter which is Sensor #2. This O2 sensor #1 may also be refered to as an air/fuel ratio sensor since on some vehicles it is. It detects the amount of oxygen in the exhaust gas compared to the outside air and then vehicle’s computer adjusts the air/fuel ratio going into the engine. The sensor is less effective when the exhaust gas temperature is low, so it includes a heater which is activated to help get better readings from the A/F O2 sensor. Essentially this P0031 Hyundai code means that the resistance of the heater circuit is lower than normal. In most cases, that resistance level must fall below 0.8 A to trigger the DTC code. Note, this code is very similar in nature to P0032 Hyundai, P0051 Hyundai, and P0052 Hyundai

Symptoms

Possible sumptoms of OBD code P0031 Hyundai
Most likely you’ll not notice any symptoms other than the MIL (malfunction indicator lamp, a.k.a. the check engine light) will illuminate.

Causes

Possible causes of OBD code P0031 Hyundai
A P0031 Hyundai DTC trouble code may be caused by one or more of the following: A short or open in the heater circuit in the sensor A failed O2 sensor heater Wiring/connectors broken/frayed leading to sensor and/or relay Failed PCM/ECM

Possible Solutions

To fix a P0031 Hyundai DTC code, you’ll need to do a proper diagnosis. To do that, you’ll want to inspect the wiring and connectors leading to the sensor. Also if equipped with a heater relay and fuse, you’ll want to check those as well. Use a digital volt ohm meter to: check for 12 volts at the heater circuit feed (hint: unplug the sensor and check at the wiring connector to do this measurement) check the ground circuit for continuity measure the resistance of the heater circuit (done on the sensor itself) measure the resistance and voltage of the wiring Refer to a service manual for the correct specifications (volts, ohms) for your vehicle. On some Toyota vehicles this code is triggered when the resistance of the heater circuit is below 0.8 A. With that said, a common fix for this DTC is to replace the air/fuel (O2 oxygen) sensor #1 on bank 1. Please keep in mind that OEM (original equipment) replacement sensors are recommended (from the dealer). Aftermarket sensors can be less reliable and of poorer quality (not always, but more often). There’s also a chance that replacement parts for the P0031 Hyundai code may also fall under a federal emissions warranty (check with your dealer to see if it’s covered).

Related Codes

P0010 Hyundai P0011 Hyundai P0012 Hyundai P0021 Hyundai P0022 Hyundai


The OBD2 Code Information Be Applicable For Hyundai:

2013 Hyundai i30,2013 Hyundai i20,2013 Hyundai Santa Fe,2013 Hyundai Langdong,2013 Hyundai HB20X,2013 Hyundai HB20S,2013 Hyundai HB20,2012 Hyundai i40,2011 Hyundai ix35,2011 Hyundai ix20,2011 Hyundai i10,2011 Hyundai Verna,2011 Hyundai Sonata,2011 Hyundai Azera,2011 Hyundai Avante,2010 Hyundai Accent,2009 Hyundai ix55,2009 Hyundai i20,2009 Hyundai Sonata,2008 Hyundai i800,2008 Hyundai i30,2008 Hyundai i10,2007 Hyundai Veracruz,2007 Hyundai Elantra,2007 Hyundai Coupe,2006 Hyundai Getz,2005 Hyundai Tucson,2005 Hyundai Trajet,2005 Hyundai Terracan,2005 Hyundai Sonata,2005 Hyundai Santa Fe,2005 Hyundai Portico Concept,2005 Hyundai Matrix,2005 Hyundai HED 1 Concept,2005 Hyundai Grandeur,2005 Hyundai Getz,2005 Hyundai Coupe,2004 Hyundai HCD8 Concept,2004 Hyundai Elantra,2004 Hyundai E-Cubed Concept,2004 Hyundai Atos Prime,2004 Hyundai Accent,2003 Hyundai CCS Concept,2002 Hyundai HCD 7 Concept,2001 Hyundai HCD 6 Concept

 

Note:

1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Hyundai makes.

2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.

3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.

4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.

5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.