Description
OBD-II Trouble Code Description for P0113 Hyundai
Intake Air Temperature Sensor 1 Circuit High
What does this mean?
OBD2 Code P0113 Hyundai definition:
The powertrain control module (PCM) monitors the temperature of the air entering the engine. The PCM supplies a 5 volt reference voltage to the Intake Air Temperature (IAT) sensor. The IAT is a thermistor that varies resistance based on temperature. As the temperature increases, resistance decreases. Low temperature results in a high signal voltage. When the PCM sees a signal voltage higher than 5 volts, it sets this P0113 Hyundai check engine light code.
Symptoms
Possible sumptoms of OBD code P0113 Hyundai
There will likely be no symptoms other than illumination of the Malfunction Indicator Lamp (MIL – Check Engine Light / Service Engine Soon).
Causes
Possible causes of OBD code P0113 Hyundai
?Internally failed IAT sensor ? Faulty connection at IAT sensor ? Open in IAT ground circuit or signal circuit ? Short to voltage in IAT signal circuit or reference circuit ?IAT harness and/or wiring routed too close to high-voltage wiring (e.g. alternator, spark plug cables, etc.) ? Faulty PCM (less likely but not impossible)
Possible Solutions
First, if you have access to a scan tool, is there an IAT reading? If the IAT reading is logical then the problem is likely intermittent. If the reading is less than -30 degrees, unplug the connector. Install a jumper wire between the harness connector signal and ground circuits. The IAT temperature reading on the scan tool should be maxed out at the high end. For example it should be 280 degrees Farenheit or higher. If it is, the wiring is okay, and it may have been the connection. If it isn’t install the jumper wire between the IAT signal circuit and the chassis ground. If now the IAT reading on the scan tool is maxed out then check for an open in the IAT ground circuit. If you get no reading at all on the scan tool, it’s likely that the sensor signal is open or the 5 volt reference is missing. Check using a DVOM (digital volt ohm meter) for a 5 volt reference. If it’s there, then unplug the connector at the PCM and check for continuity on the IAT signal circuit between the PCM connector and the IAT connector.
The OBD2 Code Information Be Applicable For Hyundai:
2013 Hyundai i30,2013 Hyundai i20,2013 Hyundai Santa Fe,2013 Hyundai Langdong,2013 Hyundai HB20X,2013 Hyundai HB20S,2013 Hyundai HB20,2012 Hyundai i40,2011 Hyundai ix35,2011 Hyundai ix20,2011 Hyundai i10,2011 Hyundai Verna,2011 Hyundai Sonata,2011 Hyundai Azera,2011 Hyundai Avante,2010 Hyundai Accent,2009 Hyundai ix55,2009 Hyundai i20,2009 Hyundai Sonata,2008 Hyundai i800,2008 Hyundai i30,2008 Hyundai i10,2007 Hyundai Veracruz,2007 Hyundai Elantra,2007 Hyundai Coupe,2006 Hyundai Getz,2005 Hyundai Tucson,2005 Hyundai Trajet,2005 Hyundai Terracan,2005 Hyundai Sonata,2005 Hyundai Santa Fe,2005 Hyundai Portico Concept,2005 Hyundai Matrix,2005 Hyundai HED 1 Concept,2005 Hyundai Grandeur,2005 Hyundai Getz,2005 Hyundai Coupe,2004 Hyundai HCD8 Concept,2004 Hyundai Elantra,2004 Hyundai E-Cubed Concept,2004 Hyundai Atos Prime,2004 Hyundai Accent,2003 Hyundai CCS Concept,2002 Hyundai HCD 7 Concept,2001 Hyundai HCD 6 Concept
Note:
1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Hyundai makes.
2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.
3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.
4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.
5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.