Description
OBD-II Trouble Code Description for P0156 Hyundai
O2 Sensor Circuit
What does this mean?
OBD2 Code P0156 Hyundai definition:
The o2 (oxygen) sensors measure oxygen content in the exhaust. The PCM (powertrain control module) then uses this information to regulate fuel injector pulse. The o2 sensors are very important for the proper operation of the engine. Innacurate or faulty o2 sensors can cause the PCM to add or take away fuel based on the faulty o2 sensor voltage which can cause a host of problems. A P0156 Hyundai code definition:the Bank 2,2 o2 sensor or the downstream (post-cat) o2 sensor on Bank 2. It is a four wire sensor. The PCM supplies a ground circuit and a reference voltage circuit of about 0.5 volts. Also for the o2 sensor heater element there is a battery voltage supply wire and another ground circuit for that. The o2 sensor heater allows the o2 sensor to warm up faster, thus achieving closed loop in less time than it would normally take for the exhaust to warm the sensor up to operating temperature. The O2 sensor varies the supplied reference voltage based on oxygen content in the exhaust. It is capable of varying from about 0.1 to 0.9 volts, 0.1 V indicating lean exhaust and 0.9 V indicating rich exhaust. This P0156 Hyundai code indicates that the Bank 2, 2 o2 sensor is stuck low for too long or isn’t active at all.
Symptoms
Possible sumptoms of OBD code P0156 Hyundai
Often post-cat o2 sensor problems present few symptoms since they are inputs to the PCM to monitor catalytic converter quality and don’t directly control fuel. sometimes no symptoms are noticeable. However the following may be possible on some vehicles: MIL (Malfunction Indicator Lamp) illumination Decrease in MPG Increase in tailpipe emissions
Causes
Possible causes of OBD code P0156 Hyundai
Potential causes of an P0156 Hyundai code include: Bad O2 sensor Signal shorted to voltage Wiring problems due to contact with exhaust components Holes in exhaust near o2 sensor
Possible Solutions
If you have access to a scan tool, check the signal voltage for the Bank 2,2 oxygen sensor with the engine at normal operating temperature. Is it stuck low currently? If so, increase RPM for a few seconds and see if it affects the reading. If it begins working with increased RPM, check for holes in the exhaust near the o2 sensor that may cause a false lean. If the exhaust pipe is intact, the sensor is sluggish, replace it. If the Bank 2,2 o2 sensor voltage reading remains low with increased RPM, unplug it and then observe the reading. It should have increased to about 0.5 volts or thereabouts. If it did, check for water intrusion or other connector problems. If none are found, replace the shorted o2 sensor. If the voltage reading is still stuck low after unplugging the sensor, then suspect a wiring problem. Using a voltmeter, with the o2 sensor unplugged, check for voltage on the signal circuit at the o2 sensor connector(PCM side). It can vary with model, but should be about 0.5 volts and not above 1 volt. If the voltage reading is too high, repair short to voltage on signal circuit. If the signal voltage checks out, suspect the PCM.
The OBD2 Code Information Be Applicable For Hyundai:
2013 Hyundai i30,2013 Hyundai i20,2013 Hyundai Santa Fe,2013 Hyundai Langdong,2013 Hyundai HB20X,2013 Hyundai HB20S,2013 Hyundai HB20,2012 Hyundai i40,2011 Hyundai ix35,2011 Hyundai ix20,2011 Hyundai i10,2011 Hyundai Verna,2011 Hyundai Sonata,2011 Hyundai Azera,2011 Hyundai Avante,2010 Hyundai Accent,2009 Hyundai ix55,2009 Hyundai i20,2009 Hyundai Sonata,2008 Hyundai i800,2008 Hyundai i30,2008 Hyundai i10,2007 Hyundai Veracruz,2007 Hyundai Elantra,2007 Hyundai Coupe,2006 Hyundai Getz,2005 Hyundai Tucson,2005 Hyundai Trajet,2005 Hyundai Terracan,2005 Hyundai Sonata,2005 Hyundai Santa Fe,2005 Hyundai Portico Concept,2005 Hyundai Matrix,2005 Hyundai HED 1 Concept,2005 Hyundai Grandeur,2005 Hyundai Getz,2005 Hyundai Coupe,2004 Hyundai HCD8 Concept,2004 Hyundai Elantra,2004 Hyundai E-Cubed Concept,2004 Hyundai Atos Prime,2004 Hyundai Accent,2003 Hyundai CCS Concept,2002 Hyundai HCD 7 Concept,2001 Hyundai HCD 6 Concept
Note:
1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Hyundai makes.
2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.
3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.
4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.
5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.