Infiniti P0341 Camshaft Position Sensor

Description

OBD-II Trouble Code Description for P0341 Infiniti

Camshaft Position Sensor “A” Circuit Range/Performance

What does this mean?

OBD2 Code P0341 Infiniti definition:
This P0341 Infiniti code basically means that the powertrain control module (PCM) detected a problem with the camshaft signal. The camshaft position sensor (CPS) sends a specific signal to the PCM for Top Dead Center on the compression stroke as well as signals indicating the position of the cam sensor. This is accomplished through a reluctor wheel attached to the camshaft that passes by the cam sensor. Any time that the signal to the PCM is inconsistent with what the signal should be, this code is set. NOTE: this code can also be set by extended cranking periods.

Symptoms

Possible sumptoms of OBD code P0341 Infiniti
The car will likely run with this code set, as it is often intermittent and also because the PCM can often operate the vehicle in “limp-in/limp-home” mode even with a cam sensor signal problem. There may be no noticeable symptoms other than: Poor fuel economy (if engine runs) Possible no start condition

Causes

Possible causes of OBD code P0341 Infiniti
A code P0341 Infiniti may mean that one or more of the following has happened: Cam sensor wiring routed too close to spark plug wiring (causing interference) Poor wiring connection at cam sensor Poor wiring connection at PCM Bad cam sensor Damaged reluctor wheel

Possible Solutions

Often relacing the sensor fixes this code, but not necessarily. Therefore it’s important to check the following: Check that the wiring isn’t routed too close to any secondary ignition components (coil, spark plug wires, etc.) Visually inspect the wiring at the sensor for any burn marks, discoloration indicative of melting or chafing Visually inspect the cam sensor for damage Visually inspect the reluctor wheel through the cam sensor port (if possible) for any missing teeth or any damage If reluctor isn’t visible from outside the engine, visual test can only be done by removing cam shaft or intake manifold (depending on engine design) If all checks out okay, then replace the sensor. Related Camshaft Trouble Codes: P0340 Infiniti

Related Codes

P0340 Infiniti P0342 Infiniti


The OBD2 Code Information Be Applicable For Infiniti:

,2013 Infiniti M35h GT,2013 Infiniti JX,2013 Infiniti FX,2011 Infiniti QX,2011 Infiniti M35h,2011 Infiniti M,2011 Infiniti JX Concept,2011 Infiniti IPL G Coupe,2011 Infiniti EX30d,2009 Infiniti G37,2009 Infiniti FX50,2009 Infiniti FX37,2009 Infiniti FX35,2009 Infiniti Essence Concept,2009 Infiniti EX37,2008 Infiniti QX56,2008 Infiniti M45x,2008 Infiniti M45s,2008 Infiniti G37 Coupe,2008 Infiniti EX35,2007 Infiniti G35 Sedan,2007 Infiniti EX Concept,2006 Infiniti QX56,2006 Infiniti Q45,2006 Infiniti M45,2006 Infiniti M35x,2006 Infiniti M35,2006 Infiniti FX45,2005 Infiniti Q45,2005 Infiniti G35,2005 Infiniti FX45,2004 Infiniti QX56,2004 Infiniti M45 Concept,2004 Infiniti I35,2003 Infiniti QX4,2003 Infiniti Q45,2003 Infiniti M45,2003 Infiniti I35,2003 Infiniti G35,2003 Infiniti FX45,2003 Infiniti FX35

 

Note:

1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Infiniti makes.

2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.

3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.

4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.

5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.