Jaguar P0107 Manifold Absolute Pressure/Barometric Pressure Circuit Low Input

Description

OBD-II Trouble Code Description for P0107 Jaguar

Manifold Absolute Pressure/Barometric Pressure Circuit Low Input

What does this mean?

OBD2 Code P0107 Jaguar definition:
The Manifold Absolute Pressure (MAP) sensor responds to changes in the intake manifold pressure (vacuum). 5 Volts is supplied to the sensor from the PCM (powertrain control module). Inside the MAP sensor is a resistor that moves in relation to manifold pressure. The resistor varies the voltage between about 1 volt to 4.5 volts (depending on engine load) and that voltage signal is returned to the PCM to indicate manifold pressure (vacuum). This signal is essential for the PCM to determine fuel delivery. A P0107 Jaguar DTC is set when the PCM sees that the MAP signal voltage is less than .25 volts which is too low.

Symptoms

Possible sumptoms of OBD code P0107 Jaguar
Anytime the MAP sensor signal is low the vehicle will likely have a very difficult time starting. Other symptoms may include: Hard to start Long cranking times Sputtering/missing Blowing black smoke Poor fuel economy Dies intermittently MIL(Malfunction Indicator Lamp) illumination

Causes

Possible causes of OBD code P0107 Jaguar
Bad MAP sensor Open or short in the signal circuit Open or short in the 5 Volt reference circuit Ground circuit open or shorted Bad PCM

Possible Solutions

First, using a scan tool with the Key on and engine running, monitor the MAP sensor voltage. If it is reading less than .5 volts, turn engine off, unplug the MAP sensor and, using a DVOM (Digital Volt/Ohm Meter) check for 5Volts on the 5 Volt reference circuit. 1. If there is not 5 Volts on the reference circuit, then check for the reference voltage at the PCM connector. If it is present at the PCM connector but not the MAP connector, repair the open in the reference circuit between the PCM and MAP harness connector. If 5 Volt reference is NOT present at the PCM connector, check powers and grounds of PCM and repair/replace as needed. (NOTE: On Chrysler products, a shorted Crank sensor, Vehicle speed sensor or any other sensor that utilizes the 5 Volt reference from the PCM can short out the 5 Volt reference. To fix simply unplug each sensor one at a time until the 5 Volt reference reappears. The last sensor unplugged is the shorted sensor.) 2. If you have a 5 Volt reference at the MAP connector, jumper the 5 volt reference circuit to the signal circuit. Now check the MAP voltage on the scan tool. It should be 4.5 to 5 Volts. If it is, replace MAP sensor. If not, repair open/short in the signal circuit wiring and re-check. 3. If all appears okay, perform a wiggle test. Start engine and manipulate the harness, connector and tap on the MAP sensor. Note any changes in voltage or engine speed. Repair connector, harness, or sensor as needed. 4. If the wiggle test checks out, use a vacuum pump (or just use your lungs) to draw a vacuum on the MAP sensor vacuum port. As you add vacuum the voltage should decrease. With no vacuum, the MAP sensor should read approximately 4.5 volts. If there is no change in MAP sensor reading on the scan tool, replace MAP sensor.

Related Codes

P0105 Jaguar P0106 Jaguar P0108 Jaguar P0109 Jaguar


The OBD2 Code Information Be Applicable For Jaguar:

2013 Jaguar XJ,2013 Jaguar XF,2013 Jaguar XFR,2012 Jaguar XKR,2012 Jaguar XJ,2012 Jaguar XFR,2012 Jaguar XF,2011 Jaguar XKR,2010 Jaguar XKR,2010 Jaguar XJ,2010 Jaguar XFR,2010 Jaguar XF,2009 Jaguar XF,2008 Jaguar XJ,2007 Jaguar XKR,2007 Jaguar XK,2006 Jaguar XJ,2003 Jaguar RD6 Concept

 

Note:

1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Jaguar makes.

2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.

3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.

4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.

5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.