Jeep P0204 Fuel Injector Cylinder 4 Activation

Description

OBD-II Trouble Code Description for P0204 Jeep

Injector Circuit/Open – Cylinder 4

What does this mean?

OBD2 Code P0204 Jeep definition:
P0204 Jeep means that the PCM detected a fault in the injector or the wiring to the injector. It monitors the injector and when the injector is activated, the PCM expects to see the voltage pulled “low” or close to zero. When the injector is switched off, the PCM expects to see a voltage that is close to battery voltage or “high”. If it doesn’t see the expected voltage the PCM will set this code. The PCM also monitors resitance in the circuit. If the resistance is excessively low or high it will set this code.

Symptoms

Possible sumptoms of OBD code P0204 Jeep
The symptoms for this code will likely be a misfire and a rough running engine. Poor acceleration. The MIL will also be illuminated.

Causes

Possible causes of OBD code P0204 Jeep
The causes of a P0204 Jeep engine light code could be any of the following: Bad injector. This is usually the cause of this code but doesn’t rule out the possibility of one of the other causes Open in the wiring to the injector Short in the wiring to the injector Bad PCM

Possible Solutions

First, using a DVOM check the resistance of the injector. If it isn’t within specs, then replace the injector. Check for voltage at the fuel injector connector. It should have 10 volts or more. Visually check the connector for damage or broken wires. Visually check the injector for damage. If you have access to an injector tester, activate the injector and see if it operates. If the injector operates, then you likely have either an open in the wiring, or a blocked injector. If you do not have access to a tester, swap the injector with another one and see if the code changes. If the code changes, then change the injector. At the PCM, remove the driver wire from the PCM connector and Ground the wire. (Make sure you have the correct wire. If you’re not sure, do not attempt) The injector should activate Replace the injector First, using a DVOM check the resistance of the injector. If it isn’t within specs, then replace the injector. Check for voltage at the fuel injector connector. It should have 10 volts or more. Visually check the connector for damage or broken wires. Visually check the injector for damage. If you have access to an injector tester, activate the injector and see if it operates. If the injector operates, then you likely have either an open in the wiring, or a blocked injector. If you do not have access to a tester, swap the injector with another one and see if the code changes. If the code changes, then change the injector. At the PCM, remove the driver wire from the PCM connector and Ground the wire. (Make sure you have the correct wire. If you’re not sure, do not attempt) The injector should activate Replace the injector


The OBD2 Code Information Be Applicable For Jeep:

,2013 Jeep Wrangler Unlimited Moab,2013 Jeep Wrangler Rubicon 10th Anniversary,2013 Jeep Grand Cherokee Trailhawk,2012 Jeep Wrangler Unlimited Altitude,2012 Jeep Wrangler Freedom Edition,2012 Jeep Wrangler Dragon Concept,2012 Jeep Wrangler Call of Duty MW3,2012 Jeep Wrangler Arctic,2012 Jeep Wrangler,2012 Jeep Liberty Arctic,2012 Jeep Grand Cherokee SRT8,2012 Jeep Grand Cherokee Concept,2011 Jeep Wrangler Mojave,2011 Jeep Wrangler Call of Duty Black Ops,2011 Jeep Wrangler,2011 Jeep Patriot,2011 Jeep Grand Cherokee UK Version,2011 Jeep Grand Cherokee,2011 Jeep Compass,2009 Jeep Wrangler Unlimited EV,2009 Jeep Patriot EV,2008 Jeep Wrangler Unlimited UK Version,2008 Jeep Wrangler UK Version,2008 Jeep Renegade Concept,2008 Jeep Patriot Back Country Concept,2008 Jeep Liberty,2008 Jeep Grand Cherokee S-Limited UK Version,2008 Jeep Grand Cherokee Overland UK Version,2008 Jeep Grand Cherokee,2008 Jeep EV Concept,2008 Jeep Cherokee,2007 Jeep Wrangler Unlimited,2007 Jeep Wrangler Rubicon,2007 Jeep Trailhawk Concept,2007 Jeep Patriot UK Version,2007 Jeep Patriot,2007 Jeep Grand Cherokee UK Version,2007 Jeep Grand Cherokee SRT-8 UK Version,2007 Jeep Compass UK Version,2007 Jeep Compass,2007 Jeep Commander UK Version,2006 Jeep Grand Cherokee SRT8,2006 Jeep Commander 4×4 Limited 5.7 HEMI,2005 Jeep Wrangler UK Version,2005 Jeep Patriot Concept,2005 Jeep Liberty Renegade 3.7,2005 Jeep Liberty CRD Limited,2005 Jeep Hurricane Concept,2005 Jeep Grand Cherokee 5.7 Limited,2005 Jeep Gladiator Concept,2005 Jeep Compass Concept,2005 Jeep Cherokee UK Version,2004 Jeep Wrangler Unlimited,2004 Jeep Rescue Concept,2003 Jeep Treo Concept,2003 Jeep Grand Cherokee UK Version,2003 Jeep Cherokee UK Version,2003 Jeep Cherokee Renegade,2002 Jeep Willys2 Concept

 

Note:

1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Jeep makes.

2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.

3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.

4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.

5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.