Description
OBD-II Trouble Code Description for P0341 Jeep
Camshaft Position Sensor “A” Circuit Range/Performance
What does this mean?
OBD2 Code P0341 Jeep definition:
This P0341 Jeep code basically means that the powertrain control module (PCM) detected a problem with the camshaft signal. The camshaft position sensor (CPS) sends a specific signal to the PCM for Top Dead Center on the compression stroke as well as signals indicating the position of the cam sensor. This is accomplished through a reluctor wheel attached to the camshaft that passes by the cam sensor. Any time that the signal to the PCM is inconsistent with what the signal should be, this code is set. NOTE: this code can also be set by extended cranking periods.
Symptoms
Possible sumptoms of OBD code P0341 Jeep
The car will likely run with this code set, as it is often intermittent and also because the PCM can often operate the vehicle in “limp-in/limp-home” mode even with a cam sensor signal problem. There may be no noticeable symptoms other than: Poor fuel economy (if engine runs) Possible no start condition
Causes
Possible causes of OBD code P0341 Jeep
A code P0341 Jeep may mean that one or more of the following has happened: Cam sensor wiring routed too close to spark plug wiring (causing interference) Poor wiring connection at cam sensor Poor wiring connection at PCM Bad cam sensor Damaged reluctor wheel
Possible Solutions
Often relacing the sensor fixes this code, but not necessarily. Therefore it’s important to check the following: Check that the wiring isn’t routed too close to any secondary ignition components (coil, spark plug wires, etc.) Visually inspect the wiring at the sensor for any burn marks, discoloration indicative of melting or chafing Visually inspect the cam sensor for damage Visually inspect the reluctor wheel through the cam sensor port (if possible) for any missing teeth or any damage If reluctor isn’t visible from outside the engine, visual test can only be done by removing cam shaft or intake manifold (depending on engine design) If all checks out okay, then replace the sensor. Related Camshaft Trouble Codes: P0340 Jeep
The OBD2 Code Information Be Applicable For Jeep:
,2013 Jeep Wrangler Unlimited Moab,2013 Jeep Wrangler Rubicon 10th Anniversary,2013 Jeep Grand Cherokee Trailhawk,2012 Jeep Wrangler Unlimited Altitude,2012 Jeep Wrangler Freedom Edition,2012 Jeep Wrangler Dragon Concept,2012 Jeep Wrangler Call of Duty MW3,2012 Jeep Wrangler Arctic,2012 Jeep Wrangler,2012 Jeep Liberty Arctic,2012 Jeep Grand Cherokee SRT8,2012 Jeep Grand Cherokee Concept,2011 Jeep Wrangler Mojave,2011 Jeep Wrangler Call of Duty Black Ops,2011 Jeep Wrangler,2011 Jeep Patriot,2011 Jeep Grand Cherokee UK Version,2011 Jeep Grand Cherokee,2011 Jeep Compass,2009 Jeep Wrangler Unlimited EV,2009 Jeep Patriot EV,2008 Jeep Wrangler Unlimited UK Version,2008 Jeep Wrangler UK Version,2008 Jeep Renegade Concept,2008 Jeep Patriot Back Country Concept,2008 Jeep Liberty,2008 Jeep Grand Cherokee S-Limited UK Version,2008 Jeep Grand Cherokee Overland UK Version,2008 Jeep Grand Cherokee,2008 Jeep EV Concept,2008 Jeep Cherokee,2007 Jeep Wrangler Unlimited,2007 Jeep Wrangler Rubicon,2007 Jeep Trailhawk Concept,2007 Jeep Patriot UK Version,2007 Jeep Patriot,2007 Jeep Grand Cherokee UK Version,2007 Jeep Grand Cherokee SRT-8 UK Version,2007 Jeep Compass UK Version,2007 Jeep Compass,2007 Jeep Commander UK Version,2006 Jeep Grand Cherokee SRT8,2006 Jeep Commander 4×4 Limited 5.7 HEMI,2005 Jeep Wrangler UK Version,2005 Jeep Patriot Concept,2005 Jeep Liberty Renegade 3.7,2005 Jeep Liberty CRD Limited,2005 Jeep Hurricane Concept,2005 Jeep Grand Cherokee 5.7 Limited,2005 Jeep Gladiator Concept,2005 Jeep Compass Concept,2005 Jeep Cherokee UK Version,2004 Jeep Wrangler Unlimited,2004 Jeep Rescue Concept,2003 Jeep Treo Concept,2003 Jeep Grand Cherokee UK Version,2003 Jeep Cherokee UK Version,2003 Jeep Cherokee Renegade,2002 Jeep Willys2 Concept
Note:
1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Jeep makes.
2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.
3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.
4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.
5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.