Kia P0326 Knock Sensor Signal 1

Description

OBD-II Trouble Code Description for P0326 Kia

Knock Sensor 1 Circuit Range/Performance

What does this mean?

OBD2 Code P0326 Kia definition:
Knock sensors are used to detect engine pre-detonation (engine knock or ping). The knock sensor (KS) is usually a two wire sensor. A 5 volt reference is supplied to the sensor and there is a signal return from the knock sensor to the PCM (powertrain control module). The sensor signal wire informs the PCM when a knock occurs and in what degree of severity. The PCM will retard the spark timing to avoid pre-detonation. Most PCMs have the ability to learn spark knock trends in the engine during normal operation. If the PCM determines that the knock is out of the ordinary or that the noise level is abnormally high, P0326 Kia may set. If the PCM senses that the knock is severe and cannot be eliminated by retarding the spark timing, P0326 Kia may set. Keep in mind that knock sensors cannot distinguish between a knock from pre-detonation or one from engine problems.

Symptoms

Possible sumptoms of OBD code P0326 Kia
Symptoms of a P0326 Kia DTC may include: MIL (Malfunction Indicator Lamp) illumination Audible knocking from the engine compartment Pinging from engine under acceleration

Causes

Possible causes of OBD code P0326 Kia
Potential causes of a P0326 Kia code include: Knock sensor connector is damaged Knock sensor circuit is open or shorted to ground Knock sensor circuit is shorted to voltage Knock sensor has failed Moisture in knock sensor connectors Incorrect fuel octane PCM has failed

Possible Solutions

If an engine knock can be heard, fix the source of the mechanical problem first then retest. Make sure the proper octane of fuel was used in the engine. Using lower octane fuel than what is specified can cause a ping or pre-detonation and may cause P0326 Kia. Unplug the knock sensor and check for water or corrosion in the connector. If the knock sensor has a seal, verify there is no coolant from the engine block fouling the sensor. Repair as necessary. Turn ignition to run position with engine off. Ensure that 5 Volts are present at the KS connector. If there is, check for proper resistance between KS terminal and engine ground. You will need a vehicle specification for this. If resistance is out of specification, replace the knock sensor. If resistance is normal, plug KS back in and idle the engine. Using a scan tool in datastream, observe KS value. Does it indicate a knock is present at idle? If so, replace the knock sensor. If the knock sensor shows no knock at idle, then tap on the engine block while observing the knock signal. If it doesn’t show a signal that corresponds with the taps, replace the knock sensor. If it does, verify the knock sensor wiring isn’t routed next to ignition wires. If there was no 5 volts present at the knock sensor connector while unplugged with KOEO (Key on engine off) then go back to the PCM connector. Turn ignition off and clip the knock sensor 5 volt reference wire in a location that is easy to repair (Or remove the wire from the PCM connector). With KOEO, check for 5 volts on the PCM side of the clipped wire. If 5 volts isn’t present, suspect a bad PCM. If 5 volts IS present, repair short in 5 volt reference circuit. Since the reference circuit is a shared circuit, you will need to check all engine sensors that are fed a 5 volt reference. Unplug each sensor one at a time until the reference voltage returns. When it returns the last sensor you plugged in is the shorted sensor. If no sensors are shorted, check the wiring harness for short to voltage on reference circuit.

Related Codes

P0325 Kia

The OBD2 Code Information Be Applicable For Kia:

2013 Kia Sorento,2013 Kia Provo Concept,2013 Kia Niro Concept,2013 Kia K9,2013 Kia Cross GT Concept,2013 Kia Ceed SW,2013 Kia Ceed,2013 Kia Carens,2013 Kia CUB Concept,2012 Kia Soul,2012 Kia Rio,2012 Kia Ray,2012 Kia Picanto,2012 Kia K2,2012 Kia Grand VQ-R,2011 Kia Sportage,2011 Kia Sorento,2011 Kia Pro Ceed,2011 Kia Optima Hybrid,2011 Kia Optima,2011 Kia Naimo Concept,2011 Kia KV7 Concept,2011 Kia GT Concept,2011 Kia Cadenza,2010 Kia Venga,2010 Kia Soul,2010 Kia Sorento,2010 Kia POP Concept,2010 Kia Forte Koup,2010 Kia Forte,2010 Kia Ceed SW,2010 Kia Ceed,2009 Kia VG Concept,2009 Kia Soul,2009 Kia Optima,2009 Kia No3 Concept,2009 Kia Magentis,2009 Kia Borrego,2008 Kia eco ceed Concept,2008 Kia Pro-cee-d,2008 Kia Picanto,2008 Kia KOUP Concept,2007 Kia cee-d,2007 Kia Rondo,2007 Kia Kue Concept,2007 Kia Carens,2006 Kia Sportage,2006 Kia Spectra

 

Note:

1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Kia makes.

2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.

3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.

4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.

5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.