Description
OBD-II Trouble Code Description for P0341 Kia
Camshaft Position Sensor “A” Circuit Range/Performance
What does this mean?
OBD2 Code P0341 Kia definition:
This P0341 Kia code basically means that the powertrain control module (PCM) detected a problem with the camshaft signal. The camshaft position sensor (CPS) sends a specific signal to the PCM for Top Dead Center on the compression stroke as well as signals indicating the position of the cam sensor. This is accomplished through a reluctor wheel attached to the camshaft that passes by the cam sensor. Any time that the signal to the PCM is inconsistent with what the signal should be, this code is set. NOTE: this code can also be set by extended cranking periods.
Symptoms
Possible sumptoms of OBD code P0341 Kia
The car will likely run with this code set, as it is often intermittent and also because the PCM can often operate the vehicle in “limp-in/limp-home” mode even with a cam sensor signal problem. There may be no noticeable symptoms other than: Poor fuel economy (if engine runs) Possible no start condition
Causes
Possible causes of OBD code P0341 Kia
A code P0341 Kia may mean that one or more of the following has happened: Cam sensor wiring routed too close to spark plug wiring (causing interference) Poor wiring connection at cam sensor Poor wiring connection at PCM Bad cam sensor Damaged reluctor wheel
Possible Solutions
Often relacing the sensor fixes this code, but not necessarily. Therefore it’s important to check the following: Check that the wiring isn’t routed too close to any secondary ignition components (coil, spark plug wires, etc.) Visually inspect the wiring at the sensor for any burn marks, discoloration indicative of melting or chafing Visually inspect the cam sensor for damage Visually inspect the reluctor wheel through the cam sensor port (if possible) for any missing teeth or any damage If reluctor isn’t visible from outside the engine, visual test can only be done by removing cam shaft or intake manifold (depending on engine design) If all checks out okay, then replace the sensor. Related Camshaft Trouble Codes: P0340 Kia
The OBD2 Code Information Be Applicable For Kia:
2013 Kia Sorento,2013 Kia Provo Concept,2013 Kia Niro Concept,2013 Kia K9,2013 Kia Cross GT Concept,2013 Kia Ceed SW,2013 Kia Ceed,2013 Kia Carens,2013 Kia CUB Concept,2012 Kia Soul,2012 Kia Rio,2012 Kia Ray,2012 Kia Picanto,2012 Kia K2,2012 Kia Grand VQ-R,2011 Kia Sportage,2011 Kia Sorento,2011 Kia Pro Ceed,2011 Kia Optima Hybrid,2011 Kia Optima,2011 Kia Naimo Concept,2011 Kia KV7 Concept,2011 Kia GT Concept,2011 Kia Cadenza,2010 Kia Venga,2010 Kia Soul,2010 Kia Sorento,2010 Kia POP Concept,2010 Kia Forte Koup,2010 Kia Forte,2010 Kia Ceed SW,2010 Kia Ceed,2009 Kia VG Concept,2009 Kia Soul,2009 Kia Optima,2009 Kia No3 Concept,2009 Kia Magentis,2009 Kia Borrego,2008 Kia eco ceed Concept,2008 Kia Pro-cee-d,2008 Kia Picanto,2008 Kia KOUP Concept,2007 Kia cee-d,2007 Kia Rondo,2007 Kia Kue Concept,2007 Kia Carens,2006 Kia Sportage,2006 Kia Spectra
Note:
1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Kia makes.
2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.
3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.
4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.
5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.