Land Rover P0032 HO2S Heater Control Circuit High Bank 1 Sensor 1

Description

OBD-II Trouble Code Description for P0032 Land Rover

HO2S Heater Control Circuit High

What does this mean?

OBD2 Code P0032 Land Rover definition:
A P0032 Land Rover DTC (diagnostic trouble code) definition:the O2 sensor (oxygen sensor) located on Bank 1 in front of the catalytic converter. There is also an oxygen sensor behind the converter which is Sensor #2. This O2 sensor #1 may also be refered to as an air/fuel ratio sensor since on some vehicles it is. The sensor detects the amount of oxygen in the exhaust gas compared to the outside air and then vehicle’s computer adjusts the air/fuel ratio going into the engine. The sensor is less effective when the exhaust gas temperature is low, so it includes a heater which is activated to help get better readings from the O2 sensor. Essentially this P0032 Land Rover code means that the resistance of the heater circuit is higher than normal. In some cases, that resistance level must be higher than 10 A to trigger the DTC code. Note, this code is very similar in nature to P0031 Land Rover, P0051 Land Rover, and P0052 Land Rover

Symptoms

Possible sumptoms of OBD code P0032 Land Rover
Most likely you’ll not notice any symptoms other than the MIL (malfunction indicator lamp, a.k.a. the check engine light) will illuminate.

Causes

Possible causes of OBD code P0032 Land Rover
A P0032 Land Rover DTC trouble code may be caused by one or more of the following: A short in the heater circuit in the sensor A failed O2 sensor heater Wiring/connectors broken/frayed leading to sensor and/or relay Failed PCM/ECM

Possible Solutions

To fix a P0032 Land Rover DTC code, you’ll need to do a proper diagnosis. To do that, you’ll want to inspect the wiring and connectors leading to the sensor. Also if equipped with a heater relay and fuse, you’ll want to check those as well. Use a digital volt ohm meter to: check for 12 volts at the heater circuit feed (hint: unplug the sensor and check at the wiring connector to do this measurement) check the ground circuit for continuity measure the resistance of the heater circuit (done on the sensor itself) measure the resistance and voltage of the wiring Refer to a service manual for the correct specifications (volts, ohms) for your vehicle. On some Toyota vehicles this code is triggered when the resistance of the heater circuit is above 10 A. With that said, a common fix for this DTC is to replace the air/fuel (O2 oxygen) sensor #2 on bank 1. Please keep in mind that OEM (original equipment) replacement sensors are recommended (from the dealer). Aftermarket sensors can be less reliable and of poorer quality (not always, but more often). There’s also a chance that replacement parts for the P0032 Land Rover code may also fall under a federal emissions warranty (check with your dealer to see if it’s covered).

Related Codes

P0010 Land Rover P0011 Land Rover P0012 Land Rover P0021 Land Rover P0022 Land Rover


The OBD2 Code Information Be Applicable For Land Rover:

2013 Land Rover,2012 Land Rover,2011 Land Rover,2010 Land Rover,2009 Land Rover ,2008 Land Rover,2007 Land Rover,2006 Land Rover,2005 Land Rover,2004 Land Rover,2003 Land Rover,2002 Land Rover

 

Note:

1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Land Rover makes.

2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.

3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.

4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.

5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.