Land Rover P0147 O2 Sensor Heater Circuit Malfunction Bank 1 Sensor 3

Description

OBD-II Trouble Code Description for P0147 Land Rover

O2 Sensor Heater Circuit

What does this mean?

OBD2 Code P0147 Land Rover definition:
O2 (Oxygen) sensors contain a heating element that allows the sensor to reach operating temperature quickly. This lowers emissions since it allows the engine to reach closed loop faster and also allows the engine to stay in closed loop at idle. The heater circuit is supplied a 12 V battery feed from the PCM or ignition circuit (depending on model) and a ground. The PCM (powertrain control module) monitors how long it takes for the sensors to become active after engine start-up. If it takes too long for the o2 sensors to reach operating temperature, this P0147 Land Rover can set.

Symptoms

Possible sumptoms of OBD code P0147 Land Rover
For this particular o2 sensor, there may be no noticeable symptoms other than: MIL (Malfunction Indicator Lamp) illumination Poor/ rough idle

Causes

Possible causes of OBD code P0147 Land Rover
Potential causes of an P0147 Land Rover code include: Bad o2 sensor heater circuit Bad o2 sensor Wiring harness problems

Possible Solutions

Unplug the Bank 1, 3 sensor. With KOEO (key on engine off) use a voltmeter to check for battery voltage present at the o2 sensor connector (PCM side). (You can also do this with a test light. Connect to ground and touch lead to heater circuit supply. Light should illuminate with KOEO) You should have battery voltage present. a. If voltage is present, check the ground side of the heater element also making sure a good ground is present. If it is, check for any faulty connections & then replace the o2 sensor. If you don’t have a good ground, then there is an open in the ground circuit somewhere that will need to be repaired. Look for wiring harness contact with exhaust components or broken/missing connectors, etc. b. If battery voltage isn’t present with KOEO, check for a blown fuse supplying the heater elements. You may need to get a wiring diagram for this. If the fuse is blown, you’ll need to check for a short to ground on the battery supply circuit before replacing the fuse. If you find none, and replacing the fuse re-establishes battery voltage at the o2 sensor connector, then the o2 sensor may have shorted internally, blowing the fuse. Replace it & recheck. (NOTE: it’s possible for an o2 sensor’s heater circuit to be open/shorted and the o2 sensor to still function). c. If you have no battery voltage present with KOEO and there are no blown fuses supplying the heater circuit, then check for an open on the supply circuit. You can do this by ohming the circuit with the o2 sensor unplugged and the PCM unplugged. Repair and recheck.


The OBD2 Code Information Be Applicable For Land Rover:

2013 Land Rover,2012 Land Rover,2011 Land Rover,2010 Land Rover,2009 Land Rover ,2008 Land Rover,2007 Land Rover,2006 Land Rover,2005 Land Rover,2004 Land Rover,2003 Land Rover,2002 Land Rover

 

Note:

1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Land Rover makes.

2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.

3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.

4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.

5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.