Land Rover P0215 Fuel Injection Pump Control Circuit

Description

OBD-II Trouble Code Description for P0215 Land Rover

Engine Shutoff Solenoid

What does this mean?

OBD2 Code P0215 Land Rover definition:
Information for when fuel injection pump control circuit is monitored and conditions required for DTC to be stored are not available.

Symptoms

Possible sumptoms of OBD code P0215 Land Rover
– Engine Light ON (or Service Engine Soon Warning Light)

Causes

Possible causes of OBD code P0215 Land Rover
– Defective fuel pump relay – Defective Engine – Control Module (ECM) or defective connectors or wiring

Possible Solutions

1. Ensure ignition is off. Remove fuel pump relay from Power Distribution Center (PDC). PDC is located at drivers side front corner of engine compartment. Fuel pump relay may also be referred to as fuel injection pump relay. Using 12-volt test light connected to battery voltage, check for voltage at cavity No. 85 (Black wire) in PDC for fuel pump relay. If test light illuminates brightly, go to next step. If test light does not illuminate brightly, repair open in Black wire between cavity No. 85 in PDC and ground connection. Ground connection is located on drivers side fender panel. 2. Note which terminals on fuel pump relay correspond with cavities in PDC. Using DVOM, measure resistance between terminals on fuel pump relay that corresponds with cavities No. 85 and 86 in PDC. If resistance is less than 100 ohms, go to next step. If resistance is 100 ohms or more, replace fuel pump relay. 3. Ensure ignition is off. Disconnect ECM connector. ECM is located on drivers side of engine, just in front of fuel transfer pump and contains a 50-pin connector. Using 12-volt test light connected to battery voltage, check for voltage at terminals No. 30 (Black/Tan wire) and No. 49 (Black/Tan wire) on ECM connector. If test light illuminates brightly at both terminals, go to next step. If test light does not illuminate brightly at any terminal, repair open ground circuit on Black/Tan wire between ECM and ground connection. Ground connection is located at ground connection for negative battery terminal. 4. Ensure fuel pump relay is still removed from PDC and ECM connector is still disconnected. Using DVOM, measure resistance between cavity No. 86 (Brown/White wire) in PDC for fuel pump relay and terminal No. 36 (Brown/White wire) on ECM connector. If resistance is less than 5 ohms, go to next step. If resistance is 5 ohms or more, repair open in Brown/White wire between PDC and ECM. 5. Ensure fuel pump relay is still removed from PDC and ECM connector is still disconnected. Using DVOM, measure resistance between ground and cavity No. 86 (Brown/White wire) in PDC for fuel pump relay. If resistance is 5 ohms or more, go to next step. If resistance is less than 5 ohms, repair short to ground in Brown/White wire between PDC and ECM. 6. It is assumed that ECM is defective and should be replaced. Before installing replacement ECM, ensure all DTCs have been repaired to prevent damaging replacement ECM. Source: mopar1973man.com


The OBD2 Code Information Be Applicable For Land Rover:

2013 Land Rover,2012 Land Rover,2011 Land Rover,2010 Land Rover,2009 Land Rover ,2008 Land Rover,2007 Land Rover,2006 Land Rover,2005 Land Rover,2004 Land Rover,2003 Land Rover,2002 Land Rover

 

Note:

1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Land Rover makes.

2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.

3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.

4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.

5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.