Land Rover P1000 OBD system readiness test not complete

Description

OBD-II Trouble Code Description for P1000 Land Rover

OBD-II Monitor Testing Incomplete

OBD-II Trouble Code Description for P1000 Land Rover

OBD system readiness test not complete

What does this mean?

OBD2 Code P1000 Land Rover definition:
The OBD monitors are performed during the OBD Drive Mode. The P1000 Land Rover will be stored in continuous memory if any of the OBD monitors do not complete their full diagnostic check.

Causes

Possible causes of OBD code P1000 Land Rover
? Vehicle is new from the factory ? Battery or PCM had recently been disconnected ? An OBD monitor failure had occurred before completion of an OBD drive mode ? The PCM DTCs have recently been cleared with a M-MDS ? The PCM has been flashed and the vehicle has not yet completed an OBD drive mode.

Possible Solutions

Diagnostic procedure

STEP	INSPECTI Land RoverON		ACTION Land Rover
1	VERIFY FREEZE FRAME DATA HAS BEEN RECORDE Land RoverD ???Has the FREEZE FRAME DATA been recorded?	Yes	Go to the next step.
1		No	Record the FREEZE FRAME DATA on the repair order, then go to the next step.
2	VERIFY REPAIR INFORMATION AVAILABILIT Land RoverY ???Verify related service repair information availability. ???Is any related repair information available?	Yes	Perform repair or diagnosis according to the available repair information. If the vehicle is not repaired, go to the next step.
2		No	Go to the next step.
3	CHECK Land Rover FOR ANY OTHER DTCS ???Where any other DTCs received with the P1000 Land Rover?	Yes	Go to the applicable DTC inspection.
3		No	Go to the next step.
4	REQUEST TO CLEAR Land Rover DTC P1000 Land Rover Note ???A complete OBD drive mode has not yet been performed to clear the DTC P1000 Land Rover from the PCM. ???Has the customer requested the DTC P1000 Land Rover be cleared?	Yes	Complete an OBD drive mode, then go to the next step.
4		No	Inform the customer that if the law in your area required additional driving in order to clear the DTC P1000 Land Rover from the PCM memory, it must be complete before an inspection/maintenance test.
5	VERIFY THAT DTC P1000 Land Rover TROUBLES Land RoverHOOTING IS COMPL Land RoverETED ???Make sure to reconnect all disconnected connectors. ???Clear the DTC from the PCM memory using the M-MDS. ???Start the engine and warm-up to normal operating temperature. ???Run the vehicle under the FREEZE FRAME DATA stored condition. ???Retrieve the DTC using the M-MDS. ???Is the PENDI Land RoverNG CODE same DTC present?	Yes	Replace PCM, then go to the next step.
5		No	Go to the next step.
6	VERIFY AFTER REPAIR PROCE Land RoverDURE ???Perform “After Repair Procedure”. ???Is there any DTC present?	Yes	Go to the applicable DTC inspection.
6		No	Troubleshooting completed.

Mercedes OBD-II Trouble Code Description for P1000 Land Rover

Electronic Gear Selector Module: Defective N15/5

The OBD2 Code Information Be Applicable For Land Rover:

2013 Land Rover,2012 Land Rover,2011 Land Rover,2010 Land Rover,2009 Land Rover ,2008 Land Rover,2007 Land Rover,2006 Land Rover,2005 Land Rover,2004 Land Rover,2003 Land Rover,2002 Land Rover

Note:

1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Land Rover makes.

2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.

3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.

4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.

5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.