Description
OBD-II Trouble Code Description for P0453 Lincoln
Evaporative Emission System Pressure Sensor/Switch High
What does this mean?
OBD2 Code P0453 Lincoln definition:
The EVAP (Evaporative Emissions) System allows fuel tank vapors to be purged into the engine and burnt rather than expelled into the atmosphere as harmful emissions. The EVAP system contains a pressure sensor to check the integrity of the system. Periodically, the EVAP system performs a pressure test to check that there are no leaks in the system. It uses this sensor, also known as a fuel tank pressure (FTP) sensor to check for leaks. Basically P0453 Lincoln means the PCM (Powertrain Control Module) noticed the EVAP Pressure sensor or FTP is indicating a higher than normal pressure (above 4.5 Volts) in the EVAP system. NOTE: On some vehicles the FTP is a part of the fuel pump assembly in the tank.
Symptoms
Possible sumptoms of OBD code P0453 Lincoln
There will likely be no noticeable symptoms along with this code other than the MIL (Malfunction Indicator Lamp), commonly known as Check Engine Light illumination. However, there may be noticeable fuel odors in some cases.
Causes
Possible causes of OBD code P0453 Lincoln
A P0453 Lincoln DTC trouble code may be caused by one or more of the following: Open on FTP sensor signal wire Short to voltage on FTP sensor signal wire Bad FTP sensor Abnormally high pressure in fuel tank due to blockage in EVAP purge hoses or overfilled tank Loose/damaged FTP sensor connector Loss of ground to the sensor
Possible Solutions
Using an scan tool access FTP sensor value with Key on Engine off (KOEO). Normal value is usually somewhere near 2.5 Volts at atmospheric pressure (may fluctuate some due to altitude). It shouldn’t ever be above 4.5 Volts. 1) If it is close to 2.7V with the gas cap off, the problem is likely intermittent. Using a Digital Volt Ohm Meter, measure the voltage on the signal wire while trying to induce the problem by wiggle testing all the wiring at the FTP sensor. If the voltage fluctuates when wiggle testing, check for connector problems; i.e. water in the connector, broken or chafed wiring. 2) If the value shown on the scan tool is above 4.5V, unplug the sensor (if possible) and check for voltage again. If the high voltage is still present when unplugged, inspect wiring harness for a short to voltage on the signal wire. If the high voltage disappears when unplugging the sensor, check for a good ground to the sensor and proper reference voltage. If you have a good ground and 5 Volts reference voltage, replace the FTP sensor since it’s likely shorted out.
The OBD2 Code Information Be Applicable For Lincoln:
2013 Lincoln MKZ,2013 Lincoln MKT,2013 Lincoln MKS,2013 Lincoln MKC,2012 Lincoln MKZ,2011 Lincoln MKX,2010 Lincoln MKZ,2010 Lincoln MKT,2009 Lincoln MKS,2009 Lincoln C Concept,2008 Lincoln MKT Concept,2007 Lincoln Navigator,2007 Lincoln MKZ,2007 Lincoln MKX,2007 Lincoln MKR Concept,2006 Lincoln Zephyr,2006 Lincoln Mark LT,2006 Lincoln MKS Concept,2004 Lincoln Mark X Concept,2004 Lincoln Aviator Concept,2003 Lincoln Town Car,2003 Lincoln Aviator,2001 Lincoln MK9
Note:
1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Lincoln makes.
2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.
3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.
4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.
5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.