Mazda P0475 Exhaust Pressure Control Valve Malfunction

Description

OBD-II Trouble Code Description for P0475 Mazda

Exhaust Pressure Control Valve

What does this mean?

OBD2 Code P0475 Mazda definition:
Exhaust Back Pressure Regulator – Is a variable position valve that controls exhaust back pressure during cold ambient temperatures to increase cab heat and decrease the amount of time needed to defrost the windshield. The PCM uses the measured exhaust back pressure, (ambient) intake air temperature, engine oil temperature and engine load to determine the desired exhaust back pressure. Valve position is controlled by switching the output signal circuit to 12 volts inside the PCM. On/off time is modulated from 0 to 99 % dependent upon the exhaust back pressure desired. Upon each initial engine start-up, the PCM exercises the exhaust back pressure valve by commanding it to cycle on and off once. If upon start-up the temperature of intake air sensed by the IAT sensor is < 37¡ãF (5¡ãC) and the oil temperature sensed by the EOT sensor is between 32¡ã-140¡ãF (0-60¡ãC) it will continue to keep the back pressure valve partially closed. As the oil temperature rises during engine operation, the PCM will control the valve in response to the rising oil temperature.

Symptoms

Possible sumptoms of OBD code P0475 Mazda
– Engine Light ON (or Service Engine Soon Warning Light)

Causes

Possible causes of OBD code P0475 Mazda
– Exhaust Back Pressure Valve The Error code is generally activated on detection of the following conditions: An open or shorted to ground control circuit can be detected by an on demand output circuit check performed during the engine off test. Problems with either the Exhaust Back Pressure Device or the tube between the exhaust manifold and the EBP sensor can be detected during the exhaust back pressure step test, in which the PCM commands and then measures a specific preprogrammed pressure and then measures time for pressure decay during the engine running test. If the PCM detects an EBP, EOT or IAT sensor fault it will disable the exhaust back pressure regulator.

Possible Solutions

Check the Exhaust Back Pressure Valve (EBPV) butterfly valve is opening and closing freely and not sticking. If it seems to move freely you can then check the connector and circuit for the EBPV solenoid.


The OBD2 Code Information Be Applicable For Mazda:

2013 Mazda MX-5,2013 Mazda CX-9,2013 Mazda CX-5,2013 Mazda 6,2013 Mazda 5,2013 Mazda 3,2012 Mazda CX-5,2012 Mazda BT-50,2012 Mazda 3,2011 Mazda 6,2011 Mazda 5,2011 Mazda 2,2010 Mazda CX-7,2010 Mazda 3,2009 Mazda RX-8,2009 Mazda MX-5,2009 Mazda CX9,2009 Mazda 6,2009 Mazda 2,2008 Mazda MX-5,2008 Mazda 6,2008 Mazda 5,2008 Mazda 2,2007 Mazda CX-9,2007 Mazda CX-7,2006 Mazda MX5,2006 Mazda 6,2006 Mazda 3,2005 Mazda Atenza,2005 Mazda 6,2004 Mazda MPV,2004 Mazda 6,2004 Mazda 5,2004 Mazda 3,2003 Mazda RX-8

 

Note:

1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Mazda makes.

2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.

3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.

4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.

5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.