Mini P0385 Crankshaft Position Sensor B Circuit

Description

OBD-II Trouble Code Description for P0385 Mini

Crankshaft Position Sensor “B” Circuit

What does this mean?

OBD2 Code P0385 Mini definition:
The crankshaft position sensor (CKP) measures crankshaft location and relays this information to the PCM (Powertrain Control Module). Depending on the vehicle, the PCM uses this crankshaft position information to time the spark properly or on some systems it is only for misfire detection and does not control spark timing. The CKP sensor is stationary and works in harmony with a reluctor ring (or toothed ring) that is attached to the crankshaft. As this reluctor ring passes in front of the CKP sensor, the magnetic field created by the CKP sensor is interrupted and this creates a square wave voltage signal that the PCM interprets as crankshaft position. If the PCM detects that there are no crankshaft pulses or if it sees a problem with the pulses on the output circuit, P0385 Mini will set.

Symptoms

Possible sumptoms of OBD code P0385 Mini
NOTE: If the crank sensor is used only for misfire detection and NOT spark timing (this varies with the vehicle), the vehicle should start and run with MIL (Malfunction indicator lamp) illumination. Also, some vehicles require several key cycles to illuminate the MIL. If this is the case, there may be no MIL illumination until the problem often enough over time. If the crank sensor is used for BOTH misfire detection and spark timing, the vehicle may or may not start. Symptoms may include: Vehicle may not start (see above) Vehicle may run rough or misfire MIL illumination

Causes

Possible causes of OBD code P0385 Mini
Damaged CKP sensor connector Damaged reluctor ring (missing teeth or not turning due to sheared-off keyway) Sensor output open Sensor output shorted to ground Sensor output shorted to voltage Failed crank sensor Failed PCM

Possible Solutions

Using a scan tool, check if, when engine is running or cranking, that there is an RPM signal. If there is no RPM reading, then visually inspect the crank Sensor Bnd connector for any damage and repair as necessary. If there is no visible damage, and you have access to a scope, you could check the CKP 5 Volt square wave pattern. If you do not, then, obtain a resistance reading of your crank sensor from a repair manual. (There are so many different types of crank sensors that there’s no way to put here which resistance reading is correct). Then check the resistance of the CKP sensor by disconnecting the Sensor Bnd measuring resistance of the sensor. (It is best to check resistance readings from the PCM connector. This rules out any wiring problems from the start. But it does require some mechanical skill and shouldn’t be performed if you’re not familiar with automobile electrical systems). Is the sensor within resistance specs? If not, replace the CKP sensor. If so, recheck resistance reading from the PCM connector. Is the reading still okay? If not, repair open or short in the wiring to the crank Sensor Bnd re-check. If the reading is okay, the problem is intermittent or the PCM may be at fault. Try reconnecting and checking for RPM signal again. If there is now an RPM signal, wiggle test the wiring harness to try and induce the fault.

Related Codes

P0335 Mini P0335 Mini P0385 Mini P0016 Mini P0017 Mini P0018 Mini P0019 Mini P0335 Mini P0336 Mini P0337 Mini P0338 Mini P0339 Mini P0385 Mini P0386 Mini P0387 Mini P0388 Mini P0389 Mini


The OBD2 Code Information Be Applicable For Mini:

2013 Mini Vision Concept,2013 Mini Roadster,2013 Mini Cooper,2013 Mini Countryman,2013 Mini Clubvan Camper,2013 Mini Clubvan,2013 Mini Clubman Bond Street,2012 Mini Rocketman Concept,2012 Mini Coupe,2012 Mini Clubvan Concept,2012 Mini Bayswater,2012 Mini Baker Street,2011 Mini WRC,2010 Mini Scooter,2009 Mini Cooper,2008 Mini One,2008 Mini Cooper,2008 Mini Clubman,2007 Mini Cooper,2006 Mini Concept,2005 Mini Cooper,2004 Mini XXL,2004 Mini Cooper,2002 Mini Cooper,2000 Mini Seven,2000 Mini Cooper

 

Note:

1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Mini makes.

2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.

3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.

4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.

5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.