Mini P1000 OBD system readiness test not complete

Description

OBD-II Trouble Code Description for P1000 Mini

OBD-II Monitor Testing Incomplete

OBD-II Trouble Code Description for P1000 Mini

OBD system readiness test not complete

What does this mean?

OBD2 Code P1000 Mini definition:
The OBD monitors are performed during the OBD Drive Mode. The P1000 Mini will be stored in continuous memory if any of the OBD monitors do not complete their full diagnostic check.

Causes

Possible causes of OBD code P1000 Mini
? Vehicle is new from the factory ? Battery or PCM had recently been disconnected ? An OBD monitor failure had occurred before completion of an OBD drive mode ? The PCM DTCs have recently been cleared with a M-MDS ? The PCM has been flashed and the vehicle has not yet completed an OBD drive mode.

Possible Solutions

Diagnostic procedure

STEP

INSPECTI MiniON

ACTION Mini
1
VERIFY FREEZE FRAME DATA HAS BEEN RECORDE MiniD
???Has the FREEZE FRAME DATA been recorded?
Yes
Go to the next step.
No
Record the FREEZE FRAME DATA on the repair order, then go to the next step.
2
VERIFY REPAIR INFORMATION AVAILABILIT MiniY
???Verify related service repair information availability.
???Is any related repair information available?
Yes
Perform repair or diagnosis according to the available repair information.
If the vehicle is not repaired, go to the next step.
No
Go to the next step.
3
CHECK Mini FOR ANY OTHER DTCS
???Where any other DTCs received with the P1000 Mini?
Yes
Go to the applicable DTC inspection.
No
Go to the next step.
4
REQUEST TO CLEAR Mini DTC P1000 Mini
Note
???A complete OBD drive mode has not yet been performed to clear the DTC P1000 Mini from the PCM.

???Has the customer requested the DTC P1000 Mini be cleared?
Yes
Complete an OBD drive mode, then go to the next step.
No
Inform the customer that if the law in your area required additional driving in order to clear the DTC P1000 Mini from the PCM memory, it must be complete before an inspection/maintenance test.
5
VERIFY THAT DTC P1000 Mini TROUBLES MiniHOOTING IS COMPL MiniETED
???Make sure to reconnect all disconnected connectors.
???Clear the DTC from the PCM memory using the M-MDS.
???Start the engine and warm-up to normal operating temperature.
???Run the vehicle under the FREEZE FRAME DATA stored condition.
???Retrieve the DTC using the M-MDS.
???Is the PENDI MiniNG CODE same DTC present?
Yes
Replace PCM, then go to the next step.
No
Go to the next step.
6
VERIFY AFTER REPAIR PROCE MiniDURE
???Perform “After Repair Procedure”.
???Is there any DTC present?
Yes
Go to the applicable DTC inspection.
No
Troubleshooting completed.

Mercedes OBD-II Trouble Code Description for P1000 Mini

Electronic Gear Selector Module: Defective N15/5

The OBD2 Code Information Be Applicable For Mini:

2013 Mini Vision Concept,2013 Mini Roadster,2013 Mini Cooper,2013 Mini Countryman,2013 Mini Clubvan Camper,2013 Mini Clubvan,2013 Mini Clubman Bond Street,2012 Mini Rocketman Concept,2012 Mini Coupe,2012 Mini Clubvan Concept,2012 Mini Bayswater,2012 Mini Baker Street,2011 Mini WRC,2010 Mini Scooter,2009 Mini Cooper,2008 Mini One,2008 Mini Cooper,2008 Mini Clubman,2007 Mini Cooper,2006 Mini Concept,2005 Mini Cooper,2004 Mini XXL,2004 Mini Cooper,2002 Mini Cooper,2000 Mini Seven,2000 Mini Cooper

 

Note:

1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Mini makes.

2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.

3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.

4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.

5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.