Description
OBD-II Trouble Code Description for P0108 Nissan
Manifold Absolute Pressure/Barometric Pressure Circuit High Input
What does this mean?
OBD2 Code P0108 Nissan definition:
The MAP (Manifold Absolute Pressure) sensor measures engine manifold negative air pressure. It’s usually a three wire sensor: a ground wire, a 5 volt reference wire from the PCM (Powertrain Control Module) to the MAP sensor, and a signal wire that informs the PCM of the MAP sensor voltage reading as it changes. The higher the engine vacuum, the lower the voltage reading. The voltage should range between about 1 volt (at idle) to about 5 volts (WOT wide open throttle). If the PCM sees the voltage reading from the MAP sensor is greater than 5 Volts, or if the voltage reading is higher than what the PCM considers normal under certain circumstances, a P0108 Nissan DTC will set.
Symptoms
Possible sumptoms of OBD code P0108 Nissan
MIL (Malfunction Indicator Lamp) will likely be on Engine may run poorly Engine may not run at all Fuel mileage may decrease Presence of black smoke at exhaust
Causes
Possible causes of OBD code P0108 Nissan
Bad MAP sensor Leak in vacuum supply line to MAP sensor Engine vacuum leak Short on signal wire to PCM Short on reference voltage wire from PCM Open in ground circuit to MAP Worn engine causing low vacuum
Possible Solutions
A good way to diagnose if the MAP sensor is to blame would be to compare the KOEO (key on engine off) MAP sensor reading on a scan tool with the Barometric pressure reading. They should be the same because they both measure atmospheric pressure. If the MAP reading is greater than 0.5 volt off of the BARO reading, then replacing the MAP sensor would likely fix the problem. Otherwise, start the engine and observe the MAP reading at idle. It should normally be about 1.5 volts (varies according to altitude). a. If it is, the problem is likely intermittent. Check all the vacuum hoses for damage and replace as necessary. You can also try wiggle testing the harness and connector to reproduce the problem. b. If the scan tool MAP reading is more than 4.5 volts, check the actual engine vacuum reading with the engine running. If it is less than 15 or 16 in. Hg, then the PCM is probably not seeing enough vacuum (due to a worn engine, perhaps) for a given operating condition (which causes a higher than normal voltage signal to the PCM) and setting the code. Repair the engine vacuum problem and retest. c. But, if the actual engine vacuum reading is 16 in. Hg or more, then unplug the MAP sensor. The scan tool MAP reading should indicate that there is no voltage present. Check that the ground from the PCM is intact and also that the MAP sensor connector and terminals are tight. If the connection is good, then replace the map sensor. d. However if, with KOEO, & the MAP sensor unplugged, the scan tool shows a voltage reading, then there may be a short in the harness to the MAP sensor. Turn the ignition off. At the PCM unplug connector and remove the MAP signal wire from the connector. Re-attach the PCM connector and see if with KOEO, the scan tool MAP reading shows voltage. If it still does, replace the PCM. If not, check for voltage on the signal wire you just removed from the PCM. If there is voltage on the signal wire, find the short in the harness and repair.
The OBD2 Code Information Be Applicable For Nissan:
2013 Nissan Pathfinder,2013 Nissan Murano,2013 Nissan Juke Nismo,2013 Nissan GT-R,2013 Nissan Altima Sedan,2013 Nissan Almera,2013 Nissan 370Z,2012 Nissan Tiida,2012 Nissan Sunny,2012 Nissan Qashqai,2012 Nissan Murano,2012 Nissan Micra ELLE,2012 Nissan Micra DIG-S,2012 Nissan Maxima,2012 Nissan Juke Shiro,2012 Nissan GT-R,2012 Nissan Extrem Concept,2011 Nissan X-Trail,2011 Nissan Rogue,2011 Nissan Quest,2011 Nissan Pivo 3 Concept,2011 Nissan Patrol,2011 Nissan Murano,2011 Nissan Micra,2011 Nissan LEAF,2011 Nissan Juke,2011 Nissan GT-R,2011 Nissan 370Z,2010 Nissan Qashqai,2010 Nissan Pathfinder,2010 Nissan Navara,2010 Nissan NV200,2010 Nissan GT-R SpecV,2010 Nissan Cube,2010 Nissan Altima Sedan,2010 Nissan Altima Coupe,2010 Nissan 370Z Roadster,2009 Nissan Xterra,2009 Nissan Pixo,2009 Nissan Note,2009 Nissan Murano,2009 Nissan Maxima,2009 Nissan Frontier,2009 Nissan 370Z,2008 Nissan X-Trail,2008 Nissan Rogue,2008 Nissan Pathfinder,2008 Nissan GT-R,2007 Nissan Sentra SE-R,2007 Nissan Mixim,2007 Nissan Altima,2006 Nissan Urge Concept,2006 Nissan Note,2006 Nissan 350Z,2005 Nissan Zaroot Concept,2005 Nissan Xterra,2005 Nissan Terrano,2005 Nissan Sport Concept,2005 Nissan Primera,2005 Nissan Pivo Concept,2005 Nissan Pickup,2005 Nissan Patrol,2005 Nissan Pathfinder,2005 Nissan Micra,2005 Nissan Altima,2004 Nissan Titan,2004 Nissan Tiida
Note:
1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Nissan makes.
2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.
3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.
4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.
5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.