Nissan P0150 Air Fuel Ratio Circuit Bank 2 Sensor 1

Description

OBD-II Trouble Code Description for P0150 Nissan

O2 Sensor Circuit

What does this mean?

OBD2 Code P0150 Nissan definition:
The O2 sensor produces a voltage based on oxygen content in the exhaust. The voltage varies between .1 and .9 Volts, .1 indicating lean and .9 indicating rich. The ECM constantly monitors this voltage while in closed loop to determine how much fuel to inject. If the ECM determines that the O2 sensor voltage was too low (less than .4 Volts) for too long (for more than 20 seconds (time varies with model)), this code is set. The code P0150 Nissan definition:Bank 2.

Symptoms

Possible sumptoms of OBD code P0150 Nissan
Depending if the problem is intermittent or not, there may be no symptoms other than MIL (malfunction indicator lamp) illumination. If the problem is constant, then symptoms may include one or more of the following: MIL illumination Engine runs rough, missing or stumbling Blows black smoke from tail pipe Engine dies Poor fuel economy

Causes

Possible causes of OBD code P0150 Nissan
Usually the cause of P0150 Nissan is a bad oxygen sensor, however this isn’t always the case. If your o2 sensors haven’t been replaced and they are old, it’s a good bet that the sensor is the problem. But, It could be caused by any of the following: Water or corrosion in the connector Loose terminals in the connector Wiring burnt on exhaust components Open or short in the wiring due to rubbing on engine components Holes in exhaust allowing unmetered oxygen into exhaust system Unmetered vacuum leak at the engine Bad o2 sensor Bad PCM

Possible Solutions

Using a scan tool, determine if the Bank 2, sensor 1 is switching properly. It should switch rapidly between rich and lean, evenly. 1. If it does, the problem is likely intermittent and you should examine the wiring for any visible damage. Then perform a wiggle test by manipulating the connector and wiring while watching the o2 sensor voltage. If it drops out, fix the appropriate part of the wiring harness where problem resides. 2. If it doesn’t switch properly, try to determine if the sensor is accurately reading the exhaust or not. Do this by removing the fuel pressure regulator vacuum supply briefly. The o2 sensor reading should go rich, reacting to the extra fuel added. Reinstall regulator supply. Then induce a lean condition by removing a vacuum supply line from the intake manifold. The o2 sensor reading should go lean, reacting to the enleaned exhaust. If the sensor operates properly, then the sensor may be okay and the problem may be holes in the exhaust or an unmetered vacuum leak in the engine (NOTE: Unmetered vacuum leaks at the engine are almost always accompanied by lean codes. Refer to the appropriate articles for diagnosing an unmetered vacuum leak). If the exhaust does have holes in it, it’s possible that the o2 sensor may be misreading the exhaust because of the extra oxygen entering the pipe via those holes 3. If none of this is the case and the o2 sensor just isn’t switching or acts sluggish, unplug the sensor and make sure there is 5 Volt reference voltage to the sensor. Then check for 12V supply to the o2 sensor’s heater circuit. Also check for continuity to ground on the ground circuit. If any of these are missing, or aren’t their proper voltage, repair open or short in the appropriate wire. The o2 sensor will not operate properly without proper voltage. If the proper voltages are present, replace the o2 sensor.


The OBD2 Code Information Be Applicable For Nissan:

2013 Nissan Pathfinder,2013 Nissan Murano,2013 Nissan Juke Nismo,2013 Nissan GT-R,2013 Nissan Altima Sedan,2013 Nissan Almera,2013 Nissan 370Z,2012 Nissan Tiida,2012 Nissan Sunny,2012 Nissan Qashqai,2012 Nissan Murano,2012 Nissan Micra ELLE,2012 Nissan Micra DIG-S,2012 Nissan Maxima,2012 Nissan Juke Shiro,2012 Nissan GT-R,2012 Nissan Extrem Concept,2011 Nissan X-Trail,2011 Nissan Rogue,2011 Nissan Quest,2011 Nissan Pivo 3 Concept,2011 Nissan Patrol,2011 Nissan Murano,2011 Nissan Micra,2011 Nissan LEAF,2011 Nissan Juke,2011 Nissan GT-R,2011 Nissan 370Z,2010 Nissan Qashqai,2010 Nissan Pathfinder,2010 Nissan Navara,2010 Nissan NV200,2010 Nissan GT-R SpecV,2010 Nissan Cube,2010 Nissan Altima Sedan,2010 Nissan Altima Coupe,2010 Nissan 370Z Roadster,2009 Nissan Xterra,2009 Nissan Pixo,2009 Nissan Note,2009 Nissan Murano,2009 Nissan Maxima,2009 Nissan Frontier,2009 Nissan 370Z,2008 Nissan X-Trail,2008 Nissan Rogue,2008 Nissan Pathfinder,2008 Nissan GT-R,2007 Nissan Sentra SE-R,2007 Nissan Mixim,2007 Nissan Altima,2006 Nissan Urge Concept,2006 Nissan Note,2006 Nissan 350Z,2005 Nissan Zaroot Concept,2005 Nissan Xterra,2005 Nissan Terrano,2005 Nissan Sport Concept,2005 Nissan Primera,2005 Nissan Pivo Concept,2005 Nissan Pickup,2005 Nissan Patrol,2005 Nissan Pathfinder,2005 Nissan Micra,2005 Nissan Altima,2004 Nissan Titan,2004 Nissan Tiida

 

Note:

1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Nissan makes.

2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.

3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.

4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.

5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.